User manual AUDIO ANALOGUE VERDI SETTANTA REV 1.3A

[. . . ] Whenever damages to the equipment occur because of fixing and modifications made form non-authorized staff or because of normal deterioration of the system. No part of this manual can be reproduced by any means, transmitted or copied for private or public use without private authorization from AUDIO ANALOGUE. The information contained in this manual is related to the data kept by AUDIO ANALOGUE at the moment of the issue o f this publication; AUDIO ANALOGUE has the right to make changes to this document without prior notice. the equipment has been projected and manufactured according to the Regulations of the Community 89/336/CEE and is marked CE. [. . . ] Always Switch off and unplug the supply cable before cleaning the equipment externally. : this operation should be made using a dry and soft cloth. never use alcohol based cleaning material. If the amplifier was carried from an extremely cold environment to and extremely hot one, it could create internal condensation, causing possible bad functioning. If this occurs, please wait for at least an hour before using it again, to allow it to gradually reach room temperature. when not used for long periods , please unplug the equipment. INSTRUCTIONS TO PUT IT OUT OF SERVICE Consult qualified staff Follow the regulations of the current legislation regarding recycling and waste disposal. One of the blue leds on its right indicates the selected source. A fix light indicates the selected source and the normal operative status of the unit, while a blinking light indicates that the unit is in the mute mode. It rotates just for a few degrees because it operates on an interrupter. Sixteen blue leds around the volume knob progressively turn on to indicate the volume level. Turntable ground connector (to be used when phono input is in use) 4) PH. If necessary, replace them with others of the same kind (see back panel). If one of the items listed above is missing, please contact your Audio Analogue retailer. After extracting the smallest items from the package, pull out the unit carefully. separate the package from the anti-shock expanded-foam protections. If batteries are not already placed in the remote controller battery slot, open the slot; insert batteries according to the indicated polarity, then close the battery slot. Where to place Verdi Settanta Verdi Settanta is a complex unit that may generate a large quantity of heat. please locate the unit in a well-ventilated place. In particular, you should leave at least 5cm around and above the unit and avoid placing it close to heat sources (radiators, heaters, amplifiers, television sets). Plugging in and connecting Verdi Settanta Before connecting Verdi Settanta to a sound source, please be sure that they're both unplugged from wall outlets. First of all, connect the source's outputs to the Verdi Settanta inputs you want to use. [. . . ] Specifications Parameter Channels: Line gain: Frequency response: Measurement conditions 20Hz-20kHz Volume ­0dB Volume ­20dB Volume ­40dB Volume 0dB, Band limits 0Hz-48kHz, inputs closed on 20 Ohm 22Hz-22kHz R->L, L->R, 10Vrms @ 1kHz on the interfering channel, measured channel input closed on 20 Ohm, 20Hz-20. TROUBLESHOOTING Symptom No led on No sound Cause Power cord incorrectly plugged Burned-out fuses Remedy Make sure the power cord is correctly plugged into the wall outlet Check fuses in the fuse panel (after unplugging the power cord from the wall outlet) above the IEC inlet and replace them with new ones of the same type Turn volume knob right Check cords and their connection Only one input led is on No sound Low volume Faulty or incorrectly plugged signal connectors between Verdi Settanta and the sources Off or incorrectly selected source Faulty or incorrectly plugged power cords between Verdi Settanta and the speakers Faulty or incorrectly plugged front panel Check if the source is on and active and if it is correctly selected using the in selector Check cords and their connection Contact your Audio Analogue retailer for connections check and front panel substitution Incorrectly selected source Select the right source using the recording selector Remote controller doesn't work No battery/ worn-out battery Place/replace battery (2 `AAA' batteries) You're standing too far or on an exceeding Get closer to the unit or reduce angle Selected in leds are on, volume control angle from the front panel works but the leds are off, or selected in Faulty or incorrectly plugged front panel Contact your Audio Analogue retailer for leds are off and volume leds are on connections check and front panel substitution If the suggested remedies should not work or the problem is not shown in the list above, please contact your local Audio Analogue retailer. Selected in leds are on, volume control works but the leds are off, or selected in leds are off and volume leds are on Recording is impossible INFORMATION ON DISPOSAL FOR USERS (PRIVATE HOUSEHOLDS) 1 In The European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin. Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. [. . . ]