User manual AUDIO TELEX AT120RC

[. . . ] the bass control in a countr-clockwise direction will provide up to 12 dB ofbass cut @ 100 IIz. ilicrophonerline Treble Tonal Control: Setting this control in the cenne position will give an overall flat hble response to the output of the amplifier. Adjusting the treble c. onhol in a clockwise direclion will provide up to l0 dB of aeble boost @ l}K Ih. Adjusting the treble control in a counter-clockwise direction will provide up to l0 dB ofheble cut lOK liz. @ This confiols the ovrall output lvel ofthe amplifio depending or the levels set for the individual inpgt mix channels as detailed above. [. . . ] When installed and activated, the cassette player will override the receiver so that only one ofthe receiver or cassette player may b operatd at once, the cassette playr haying priority. You may monitor the output of the reciver via an intemal monitor speaker. The volume ofthe monitor speaker is contolled by the vertical slider contol labelled Monitor, located cenhally on the fiont panel ofthe amplifir. Ifyou \mnt to preview the output of the receiver before sending it out live to the spakers, simply turn the amplifiers master output level control fiIly anti-clockwise to turn offthe output ofthe amplifier. Note that ifyou do this, all output is tumed ofi, including all micophone inputs. Five hming bands are availablg 2 x AM and 3 x FM: the receivers display panel will illuminate to display the relevant information. To select the desired band press the button marked Alv{/FM. Each time this button is pressed a different tuning band will be indicated on the display panel. Up to 30 preset channels may be stor4 6 for each tuning band. To store a channel operate the up and down arrow buttons tmtil you locate and are properly tuned to the radio station of your choice. Then, press the memory button which will cause the channel to flash on the display panel. Press the desired storage channel (numbered i to Oy. the radio station chosn is thn stored in that mernory location. You may autornatically search for radio statiom by oprating the up and down arrow buttons. The receiver will search fc and automatically lock on to threshold signals in the frequency band you have selected. Continue to press the up or donm arrow buttons to resume your sarch or to fine tune any station selected. Cassette Player (AT120RC-1 Only): me cassette player has 3 mique controls, and Fast Forward @F). mmitored and preyiewed in exactly the same fashion In addition, there is a gain contol located on the receiver module that controls the output level of the cassette deck (and, when a cassette is insertod has pricity over the receiver as detailed above). The cassettJ phyer may be as the one each for Eject, Rewind (REw) receiver. The cassette playef will tregin playing imnediately a casstte is insfted though the slot in front ofthe cassette playr. The REW and FF buttons will shuttle the cassette backwards or forwards respectively. Pressing both the REW and FF buttors together will reverse the playing direction of the cassette player and effectively change the side of the cassette bcing played. Pressing the eject button will eject the cass1te and switch back to the receivers output. Ifyou do not want to switch inmediately back to thi receivers output when you eject the cassefte, make sure that the gain conhol on the receiver is turned fully munter clockwise. Optional Accessorles The instrllrtion of some ofthe following optional rccessorics involves scc$s to tbc insidc of thc rmplificr. Inste[etion should only be tttemptcd by a qurlified techniciln. [. . . ] For best FM rsults, we recommend using the 75 ohm cornectiqr to a rermote antenna via 75 olun cnaxial cable. Tape Output This is a monaural RCA type connector and witl provide an output of 350 mv in to a loK ohm load. This output is sourced befor the mastei gain contol and as such, the tape output level is not influenced by the operation ofthe master gain control. 4. 5. Active Balanced, XLR Sockets For The ticrophone lnputs. 3, 2, &lrespectively. 7. with an input sensitivity of 0. 75mv @ 200 ohms. Pin oqmcctims are: pin #l-earth; pin #2-active OiSh, +); pin #3-ac-tive ooq ). [. . . ]