User manual AUDIO TELEX TX8201

[. . . ] The input sensitivity when in the line level position is 330mV (for a I Volt output) The first 6 inputs are labeled Mic. Line MiC/Line Gain: I StefeO Line Gain: output). The 2 auxiliary input channels are labeled Stereo Line 7 and Stereo Line 8. These controls should be adjusted to provide the required mix level for each individual auxiliary channel. Start with the controls set to Level 0 and tum the controls clockwise until the desired mix level for each channel is reached. The sensitivity of auxiliary inputs 7 and 8 is 180 mV (for a I volt Mastef Left & Right Output The master Left and fught controls should be adjusted to set the overall mixer level for each output channel based on the individual levels already set via the input channel gain controls. [. . . ] The four tones may be activated via a simple contact closure. To activate a tone, just short out the common terminal with the terminal labeled with the tone that you want to use. When activated, any of the four tones will mute all inputs except for channels I and2. While the tone generator function is (as default) set up to be present on both the master outputs and the direct outputs (of channels l-6), it can be disabled for all or any of the direct outputs via an internal dip switch (see the 'Intemal Adjustments' section of this manual for more details). A trim pot (R104), which is located on the pcb behind the left channel master output, may be adjusted to vary the level oftone generator output. Left Channel Output Gonnection rnis is an active balanced XLR connection with a nominal level The pin connections are; pin #l-earth; pin#Z-active (high, +); pin #3-active (low, -). of I volts @ 600 ohms. Right Channel Output Connectiofi. This is an active balanced XLR connection with a nominal level ohms. The pin connections are; pin #1-earth; pin #2-active (high, +;; pin #3-active (low, -). of I volts @ 600 Dual RCA Sockets For Output To A Stereo Tape Recorder. The top connector is the left channel output while the bottom connector is the right channel output. The tape outputs are connected before the master Left & Right output level controls so the tape output level is not affected by adjustments to the master level controls. Dual RCA Sockets For The 2 Stereo Auxiliary lnputs. connections are for auxiliary inputs 8 and 7. The top connectors are for the Left channel auxiliary inputs while the bottom connectors are for the fught channel auxiliary inputs. Reading from Left to Right across the rear panel, the 6 Active Balanced XLR Sockets For Microphone Line lnputs. Each XLR input is switchable to be either balanced mic or line (via an internal dip switch, the location and setting of which is explained in the 'Internal Adjustments' section of this manual). When set to mic level, the mic input sensitivity is lmV ( for a I Volt output). When set to line level, the input sensitivity is 330 mV (for a 1 Volt output). Pin connections are: pin #l-earth; pin#2-active (high, +;; pin #3-active (low, -). Phantom power of +15 volts is available on all 6 XLR inputs. An intemal phantom power ON-OFF switch is provided for each channel. The default setting is or ON (See the 'Intemal Adjustrnents' section of this manual for more details). Reading from left to right across the rear panel, th connection for the XLR mic/line inputs are 6, 5, 4, 3, 2, & I respectively. Direct Outputs. [. . . ] The unit ships from the faciory set to mic level. Tone Generator to Direct Output Defeat Switch. for Sigrral from the tone generator can be removed from each direc output via switch # 4 (TG) on the internal dip switch per channel. When in the ON position, the tones (when activated) are fed to th corresponding direct output as well as the master Lefl/Right outputs. When the switch #4 is set to the OFF position, the tones are onl present at the Master Ift/Right outputs. [. . . ]