User manual AUDIOBAHN ACAP651N

[. . . ] Judge for yourself, and remember what it's all about, "If it's not Bigger, Badder & Better, it's not Audiobahn. " If audio is your life, Audiobahn is the brand for you!People never stop trying to get the best product, so we will never stop making it. *To learn more about "TEAM AUDIOBAHN" please give us a call, see our website at www. audiobahninc. com, or email us at team@audiobahninc. com to learn about all the details. Table of Contents Table of Contents INTRODUCTION CAPACITOR INTRODUCTION SPECIFICATIONS CHARGING / DISCHARGING INSTALLATION AND WIRING ADJUSTMENTS AND TROUBLESHOOTING WARNING / DISCLAIMER WARRANTY 3 4 5 6 6 8 9 10-11 2 Introduction Dear Customer, Congratulations on your purchase of the worlds finest brand of car audio products. we are devoted to making our musical reproduction the very best, and we are pleased you have chosen our product. Through years of engineering expertise, hand craftsmanship, and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve. For maximum performance we recommend you have your Audiobahn product installed by an Authorized Audiobahn Dealer, as we provide specialized training through our Audiobahn Installer Training Programs. [. . . ] A capacitor will help reduce or eliminate this "alternator whine" and popping. We recommend using 1 farad of capacitance for every 1000 watts of amplifier output. This is a general rule of thumb and may be adjusted up or down depending on the efficiency, current draw, and design of the amplifiers being used. 4 Specifications Model: ACAP651N DIGITAL HYBRID AMP STYLE 12 FARAD CAPACITOR BANK W/DISTRIBUTION BLOCKS Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 000, 000 micro farad (12 Farad) Working Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24DC Surge Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28DC E. S. R. (Equivalent Series Resistance). . . . . . . . . . . . . 0. 0015 ohm @120hz/ 25°C Capacitance Tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 10% DETAILED FEATURES: a) 3 digit hi-end blue lighted amperage display meter and DC voltage meter that can measure 1 AMP and 0. 1 DCV range. b) Reverse polarity connection PCB buzz warning function. If the capacitor is connected incorrectly by reversing the positive and negative wires during the installation process, the PCB will issue a 45 second noise to warn you. c) Multiple small capacitance capacitors linked to provide the lowest inner E. S. R. d) Over voltage limit and low battery voltage limit warning. When the system voltage peeks over 17 DCV or LESS than 10 DCV. The buzzer on the PCB will issue an audible noise warning. e) Hi-end platinum plated 100% solid brass parts with chrome plated metal cover. Charging CHARGING THE CAPACITOR AND WIRING: The capacitor must be charged before connecting the power and ground cables to the capacitor. Failure to charge the capacitor will result in a large spark generated from the rapid inflow of current which can cause damage to the unit or serious injury. To Charge the capacitor: 1. Make the positive terminal connections between the capacitor and amplifier and tighten the bolt. Do not connect the battery and do not over-tighten the bolts!Caution: Stripped terminals are not covered under the capacitor's warranty. Connect the ground of the capacitor to the battery and amplifier, refer to the attached drawing. Place the supplied charging bulb or resistor between the positive terminal of the capacitor and the battery's positive terminal. Do this for 30 seconds or until the charging bulb goes out. Caution: The charging bulb will get hot!Immediately after the charging process, take out the charging bulb from the connecting wire and connect the positive cable of the battery directly to the positive terminal on the capacitor as quickly as possible. Discharging When you want to remove or disconnect the capacitor from the system you must discharge the capacitor. It will be safe to release the power of the capacitor. To Discharge the capacitor: With the battery power disconnected, place the light bulb or resistor across the capacitor's positive and negative terminals until the light goes out or for three minutes if using a resistor. DISCHARGING THE CAPACITOR: Installation and Wiring Please make sure that you have correctly and successfully charged your capacitor. [. . . ] www. audiobahn. com 10 Warranty Technical Assistance (800)488-8595 /tech@audiobahninc. com Audiobahn Consumer Product Warranty Policy Audiobahn products are manufactured with the highest quality components and some of the most advanced technology available. Because of this, we recommend that you have your new products installed by an Authorized Audiobahn Dealer. (A list of Authorized Audiobahn Dealers can be found on our web page). Warranty Period: One year from the original date of purchase. Warranty Coverage: This warranty covers manufacturer defects only. [. . . ]