User manual AUDIOBAHN DUB100

[. . . ] People never stop trying to get the best product, so we will never stop making it. *To learn more about "TEAM AUDIOBAHN" please give us a call, see our website at www. audiobahninc. com, or email us at team@audiobahninc. com to learn about all the details. Introduction Dear Customer, nsumer and . We strive to d a world m goal in Congratulations on your purchase of the worlds finest brand of car audio products. Here at DUB audio we are devoted to making our musical reproduction the very best, and we are pleased you have chosen our product. Through years of engineering expertise, hand craftsmanship, and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve. e will take hat has owcase spends to satisfy For maximum performance we recommend you have your DUB audio product installed by an Authorized DUB audio Dealer. [. . . ] Additionally, the back plate is vented with a radius aerodynamic back vent which efficiently and quickly circulates cool air around the voice coil. This allows for more excursion and higher power handling without damaging the sub. no h, but it Voice Coil The 4-layer, edge wound voice coil design of the speaker allows for a variety of impedance loads to be configured when used individually or matched with multiple subs. Please continue to the TECH TIPS section of this manual for wiring diagrams and procedures. The High Excursion subwoofers are a dual 4 ohm voice coil configuration. . ne WWW. DUBSERIES. COM 05 06 DUB Woofer Paramaters DUB100 DUB200 DUB500 Model # Vas does not represent the volume of a Box. Vas is just a parameter used when calculating a box. 29. 7Hz 32 Hz 38 Hz Fs 0. 64 0. 72 0. 74 Qts 0. 77 0. 83 0. 92 Qes 3. 79 5. 397 3. 923 Qms 86. 5 Liters 63. 99 Liters 24. 0 Liters Vas (Liters) 3. 1 Cu. Ft. ) 1. 5 ohms 1. 5 ohms 1. 5 ohms Re 0. 43 mH 0. 43 mH 0. 43mH Le 267 Grams 126. 5 grams 114. 5 Grams Mmd +/- 8 mm +/- 8 mm +/- 8 mm Xmax 500 watts 400 watts 300 watts RMS 770 sqcm 480 sqcm 330 sqcm Sd 18Hz-500Hz 20Hz-500Hz 23Hz-500Hz Freq. 93. 9 dB 92. 7 dB 91. 1 dB Efficiency(2. 8V) An EBP of less then 45 is SUGGESTED for only a sealed box and greater then 65 for a ported box. EBP 42 39 39 Theile / Small Parameters Dimensions 5 1/4" 9 1/8" 10" 0. 12 Cu. 6 3/8" 10 7/8" 12 1/8" 0. 23 Cu. Ft. 7 1/8" 13 5/8" 15 1/8" 0. 38 Cu. Ft. Depth Hole Diamater Displacement Box Parameters DUB Box Specifications All ports listed are circle ports unless otherwise stated. Surface area of a circle port = (3. 14) X (radius) (squared) Remember to build your box to the total volume, not just air space, as total volume includes all displacement. Model # DUB100 DUB200 DUB500 Space Saver Bass Design Ported Air Space (Cu. Ft. ) 0. 7 2 x 6. 5 3. 2 38 41 0. 12 0. 01 0. 75 1. 2 3 x 6. 75 6. 5 36 39 0. 23 0. 025 1. 5 1. 70 4 x 6. 5 4. 0 36 38 0. 38 0. 047 2 Everyday Bass Performer Ported Air Space (Cu. Ft. ) 1. 3 3 x 7. 5 4. 6 30 37 0. 12 0. 3 1. 5 2. 2 4x7 5. 5 32 39 0. 23 0. 05 2. 5 2. 6 4 x 7. 5 4. 7 30 35 0. 38 0. 05 3 Ultimate SPL Bass Box (not designed for competition use) Ported Air Space (Cu. Ft. ) 2. 3 4x7 3. 9 29 37 0. 12 0. 035 2. 5 3. 1 (2) 4 x 12 4. 5 29 37 0. 23 0. 16 3. 5 3. 55 (2) 4 x 11 4. 1 28 35 0. 38 0. 15 4 A port velocity of 20% or under is good for everday use and 5% or under for SPL competition . Port velocity translates to port noise, so the lower the number, the less port noise you will incur. An EBP of less then 45 is SUGGESTED for only a sealed box and greater then 65 for a ported box. EBP 42 39 39 The larger a sealed box is, the lower the sub will play, but the less power it will handle. The smaller a sealed box is, the higher the frequency the sub will play, and the more power it will handle. Model # DUB100 0. 5 1. 25 DUB200 0. 75 1. 5 DUB500 1. 25 3 Sealed Minimum (Cu. Ft. ) All sealed boxes already include the displacment for the subwoofer. NR = (Not Recommended) WWW. DUBSERIES. COM 07 DUB100 Curves 08 DUB200 Curves WWW. DUBSERIES. COM 09 DUB500 Curves 10 Enclosure and Setup Building an Enclosure To work properly, the walls of the enclosure must be rigid and not flex when subjected to high pressure generated by the speaker's operation. For optimum performance, we recommend using 3/4" MDF (Medium Density Fiberboard) and internal bracing. The enclosure should be glued together along with support of screws or nails. Because MDF is porous, it is suggested that you seal the outside with polyurethane prior to painting or carpeting. Calculating Volume Calculating is merely a matter of measuring the dimensions in inches, and using the following formula: Box Volume = (Height) x (Width) x (Depth) divided by 1728. [. . . ] Any product found to have no manufacturer defect will be returned to the sender at their cost. You must acquire a Return Authorization Number (RA #) prior to returning ANY product to Audiobahn. That Return Authorization Number (RA #) must be prominently and clearly marked on the outside of the shipping carton, or product delivery will be refused (no exceptions will be made). Please note: All shipping and handling (to and from) charges will be the sole responsibility of the consumer. [. . . ]