User manual AUDIOLINE DECT 4800

[. . . ] - User controls - 2 User controls 1 1. 2 12 11 3 4 5 Call indicator, flashes for newly recorded messages 2. Mute button/Cancel 10 9 6 7 8 123 1. 4. Call indicator Answering machine on/ Message indicator Charge monitoring lamp Paging button. 4 66 - Setting up - 3 3. 1 Safety Information Setting up NOTE Before setting-up, it is essential that you read the General Information at the beginning of this manual. 3. 2 The following items are supplied: one base station one handset with belt clip one telephone connecting cable Check contents of pack one mains power supply two standard batteries one instruction manual 3. 3 Connecting the base station Position the base station near to your telephone connection socket and to a mains socket. Your telephone works using Touch-Tone Dialling. [. . . ] 5x 8. 13 Factory settings Button Display FEATURES 5x RESET RESET 1x Number pad SETTINGS PIN?Enter the PIN code for the base station SETTINGS The factory settings are reset. External ring melody tone 1 Internal ring melody tone 2 Basis ring melody 1 Handset ringer volume 3 Base station ringer volume 3 Direct dialling off PIN 0 0 0 0 Call accept 5 rings Record calls Message tone off Receiver volume medium Flash time 1 Confirmation tone on Tone dialling Language: German Baby call off Answering machine on Standard greeting on Recording time 2 min. SOS Code 111 Button click on Automatic call accept on Call duration on Charging monitor on Monitor off Dialling blocks off Listen-in on Exception numbers off Blocks off PIN remote access 000 You can reset the handset to the factory settings once more by means of the Factory Settings function. 94 - The answering machine - 9 The answering machine The integral answering machine can digitally store up to 25 incoming messages with a total length of up to 9 minutes. In addition, a memo can be left for other users. For your greeting message, you can use two pre-recorded standard messages or you can record two messages of your own. If you have not recorded your own greeting, the standard greeting will answer automatically. Note: Even when the answering machine has already accepted the call, you can also accept the call by means of the call button . In this case, the recording of the message will be automatically terminated. The answering machine is controlled by means of the handset. Press 1 to switch on the answering machine control. 876 9 10 11 12 5 4 3 2 1 1. Start answering machine control Changeover greeting mode Record greeting Play back greeting Skip messages Switch answering machine on/off 7. Play back messages Stop button Repeat messages Play back memo Record memo Delete messages When the answering machine control is switched on, the display will change back to the normal display after ca. 30 seconds if no entries are made. 95 - The answering machine 9. 1 To switch the answering machine on, proceed as follows: Button Display Switching the answering machine on/off ANS RECORD, ANS ONLY or AM OFF Comment The messages ANS RECORD, ANS ONLY or AM OFF will appear in the display Switching on or off takes ca. 2 seconds and is confirmed by a signal tone. Hold button pressed to return to main display. When the answering machine is switched on, the symbol appears in the indicator light on the base station comes on. display and the 9. 2 9. 2. 1 Maximum recording time General settings Button Display FEATURES 6x ANSWER MAC RING DELAY 2x MSG LENGTH 1 MINUTE or 2 MINUTES Select the required length. MSG LENGTH Press and hold button The integral answering machine can digitally store up to 9 minutes of incoming messages. The maximum length of each incoming message is either 1 or 2 minutes. If the caller speaks for longer, a signal tone sounds and the call will be cut off. If there is a pause of more than 3 seconds during recording, the call will automatically be terminated with a signal tone. No more calls will be answered if the memory capacity for new messages is exhausted and the display will show the appropriate message. 96 - The answering machine 9. 2. 2 Button Display FEATURES ANSWER MAC RING DELAY TOLL SAVER or RINGS 2 to 7 Select the required number. [. . . ] o You are too far away from the base station. o You are too far away from the base station or the base station is wrongly positioned. o Place the handset properly on the base station, clean the contact surfaces on the handset and on the base station with a soft, dry cloth. If this does not help, replace the standard batteries. [. . . ]