User manual AUDIOLINE RINGFLASH 200 V1.1

[. . . ] Hotline hours are Monday to Friday, 9am to 5pm, excluding public and national holidays Starting Up Check the contents of the package Contents RF100 RF200 RingFlash unit 1 1 Power adaptor plug 1 1 Telephone connection 1 1 cable Doorbell unit 0 1 12 Volt battery 0 1 Fixing screws and wall 0 4 plugs Operating Manual 1 1 Connecting the base Connect the base as illustrated in the diagram For reasons of safety, only use the power adaptor plug and telephone connection cable supplied As soon as you switch the mains power on, the RingFlash unit will beep to confirm that it has been installed correctly If you do not hear a beep, please unplug the power connection, wait for 1 minute and then plug in the power again 0844 800 6503, cost via UK landline at time of going to print: 6p connection charge and 5p/min. Thereafter, different charges may apply if calling from a mobile phone. Hotline hours are Monday to Friday, 9am to 5pm, excluding public and national holidays Connecting the doorbell unit (RingFlash 200 only) Remove the 4 screws from the back of the Doorbell. [. . . ] Thereafter, different charges may apply if calling from a mobile phone. Hotline hours are Monday to Friday, 9am to 5pm, excluding public and national holidays Set the ring tone Your RingFlash unit has 3 ring tones to choose from Just move the slider switch on the left hand side of your product to select ring tone 1, 2 or 3 Set the Doorbell tone (RingFlash 200 only) You can choose from two different Doorbell tones, just move the slider on the left hand side of your product to select Doorbell tone 1 or 2. Set the alarm mode There are 4 alarm modes to choose from Please use the slider on the right hand side of the product to select one of the following alarm modes Mode 0 Ring alarm Off Bell alarm Bell sound from the speaker Strobe light Bell sound from and speaker speaker and strobe light Speaker Bell sound from and external speaker and shaker external shaker Strobe light Bell sound and external from speaker, shaker strobe light and external shaker Stop the ring alarm Press the STOP button on the front of the unit to stop the ring alarm for that call, even if the telephone line continues to ring. The ring alarm will return to its original setting for the next call 0844 800 6503, cost via UK landline at time of going to print: 6p connection charge and 5p/min. Thereafter, different charges may apply if calling from a mobile phone. Hotline hours are Monday to Friday, 9am to 5pm, excluding public and national holidays Using the Doorbell (RingFlash 200 only) Press the Doorbell button, the red light in the button will turn on. The RingFlash unit will sound the Doorbell tone that you have set (tone 1 or tone 2) Press the STOP button on the RingFlash unit to stop the Doorbell tone. The red light on the Doorbell button will remain on for 1 minute and then turn off Compatibility with other local devices (RingFlash 200 only) When using the RingFlash 200 and Doorbell there may occasionally be a compatibility problem with other local devices You can change the code undereath the RingFlash unit and inside the doorbell to solve this problem Underneath the RingFlash unit you will find 8 little switches underneath a cover You can change the setting of these switches to overcome any local compatibility issues When you have changed the setting of the 8 switches on the RingFlash unit you will need to change the 8 switches inside the Doorbell to match. unscrew the Doorbell from outside the Front Door. Remove the 4 screws from the back of the Doorbell. Inside you will see 8 little switches, change the setting of these switches to match those on the RingFlash unit 0844 800 6503, cost via UK landline at time of going to print: 6p connection charge and 5p/min. Thereafter, different charges may apply if calling from a mobile phone. Hotline hours are Monday to Friday, 9am to 5pm, excluding public and national holidays Refix the Doorbell outside your front door as before Wallmounting Using appropropriate screws and wall plugs (not supplied), you can wallmount your RingFlash unit using the keyholes on the base Service Hotline In the case of technical problems, you can contact our hotline service, UK Tel. 0844 800 6503 (cost via UK landline at time of going to print: 6p connection charge and 5p/ min, thereafter, different charges may apply if calling from a mobile phone). Hotline hours are Monday to Friday, 9am to 5pm, excluding public and national holidays In the case of claims under the terms of the guarantee, contact your sales outlet There is a 2 year period of guarantee. 0844 800 6503, cost via UK landline at time of going to print: 6p connection charge and 5p/min. [. . . ] Thereafter, different charges may apply if calling from a mobile phone. Hotline hours are Monday to Friday, 9am to 5pm, excluding public and national holidays Purchased the AMPLICOM equipment together with the purchase receipt All rights to claims under the terms of the guarantee in accordance with this agreement must be asserted exclusively with regard to your sales outlet Two years after the purchase and transfer of our products, claims under the terms of guarantee can no longer be asserted Declaration of Conformity This device fulfils the requirements stipulated in the EU directive: 1999/5 EU directive on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity Conformity with the above mentioned directive is confirmed by the CE symbol on the device To view the complete Declaration of Conformity, please refer to the free download available on our website www Distributed by: Audioline GmbH, D-41460 Neuss amplicomeu service-Hotline UK Tel. 0844 800 6503, cost via UK landline at time of going to print: 6p connection charge and 5p/min. [. . . ]