User manual AUDIOLINE SENSOR 500

[. . . ] 7 On the hook dialing. . . . . . . . . . . . . . . . 7 Using a headset. . . . . . . . . . . . . . . . . . . . . 8 Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pause. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Caller display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can change to speaker/headset during a call by pressing and replacing the handset. Note: Ensure the switch on the right hand side is set to the desired function headset/speaker. USING the ON-HOOK DIALING 1. Ensure that the switch on the right hand side of the phone is set to . Use the volume control on the right hand side to adjust the sound level. When the called party answers, lift the handset. · To terminate the call replace the handset. USING a HEADSET 1. Ensure that the switch on the right side of the phone is set to: 2. · Press and release to terminate the call. 7 LAST NUMBER REDIAL If the last number dialled was engaged or the call was not answered, it is possible to redial the number using the button. The telephone number will be dialled automatically. · When the called party answers, lift the handset (or headset) to converse. If the call is not answered, press and release It's also possible to lift the handset and then press the redial key. VOLUME CONTROL The sound volume in the handset or headset can be adjusted using the [VOL ] to increase the volume , and [VOL ] to decrease the volume. MUTE If during a telephone conversation, you wish to talk privately to a third party without the caller overhearing: Press the button (the word MUTE will appear on the display). To resume the conversation, press the button again. PAUSE A short pause to numbers stored in the phone book and the speed-dial memories, using this button. This may be required if the phone is connected to a PABX or if used with some network services. TELEPHONE RINGER The telephone ringer volume can be set to either high, low or off which is represented by this symbol . 8 CALLER DISPLAY Caller display allows you to see who is calling before you answer a call and to see who has called in your absense. When the service is implemented on your telephone line, seconds before your telephone rings the number of the incomming caller will appear on the display. Up to 60 incomming numbers can be stored in the call list. When the list is full, the oldest number will be deleted automatically. It is not possible to view the call list and take a new call at the same time. Caller Display is an optional telephone Network service. If the caller Display service is not implemented on your telephone line, incomming call information will not be displayed. NEW NUMBERS The words NEW CALL and the number of calls will appear on the display. The envelope symbol on the display will flash. Once the number(s) have been reviewed, NEW CALL will disappear and the indicator will stop flashing. When an incoming number is received it is assigned a call sequence number which appears on the top left hand side of the display, commencing with 01 (oldest call) up to 60 (latest call). 9 REVIEWING PHONE NUMBER Scroll the memory with the keys or . The time and date each call is received is shown on the display. [. . . ] please contact our Helpline for assistance. If the product is then found to be faulty you will be asked to return it directly to the service agent, ATLAS GENTECH (NZ) LIMITED with a copy of the purchase receipt. ATLAS GENTECH (NZ) LIMITED 87 Carbine Road, Mt Wellington, Auckland Service & Spare Parts (Toll Call): 0900 50 025 Fax: (09) 574-2722 Email: helpdesk@atlasgentech. co. nz NOTE: The guarantee does not extend to damage caused by misuse, negligence, excessive voltage, faults on the telephone line or lighting. This guarantee in no way affects your statutory right. [. . . ]