User manual AUDIOVOX 1287252A

[. . . ] P ICTURE S ELECT S OURCE ON OFF AUTO VO LUME FM S ELECT 2 5 ADV200B / ADV200S / ADV200P DVD PLAYER WITH DROP-DOWN VIDEO MONITOR HEADPHONES INPUT IR VID EO AUDI O R L 128-7252A 128-7252A 1 of 35 Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in "park" or when the vehicle's parking brake is applied. An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Warnings Do not use any solvents or cleaning materials when cleaning the video monitor. Do not use any abrasive cleaners, they may scratch the screen. [. . . ] The volume can then be adjusted using the controls on each headset. Any number of wireless headphones may be used but they must be used within a line of sight from the transmitter, as infrared transmissions, like visible light travel only in a straight line. See the documentation accompanying your Audiovox Wireless Headphones. -16- 128-7252A 16 of 35 Wired Headphones There are two 1/8" headphone jacks on the ADV200 that can be used with any standard wired stereo headphones. These jacks are controlled by the volume up / down buttons on the ADV200 or the remote control. Wireless FM Modulator The ADV200 is equipped with buit-in wireless FM Modulator*, that allows you to listen to the ADV200 audio signal by tuning your vehicle's radio to the selected frequency, (88. 3, 88. 7, 89. 1, 89. 5, 89. 9MHz). This feature is accessed by using either the FM transmitter buttons on the remote (On/Off, Channel Select) or the FM Select button on the unit. AV1 Input The AV1 video input may be connected to a Video cassette Player (VCP), video game system, or other audio / video devices. To access the A/V1 input, turn the ADV200 on and press the source button on the ADV200 or the Source button on the remote control until "AV1" is displayed on the screen. Turn the video source component on with its power button or remote control. The ADV200 is now ready to play the audio and video signals from the source connected to AV1 input. *NOTE: In certain areas where there are a large number of FM radio stations (e. g. large cities, urban areas), the reception of the FM signal from the overhead pod may not be satisfactory, resulting in static, distorted sound or signal bleed thru from strong local radio stations. This is not a defect in the product, but the result of a stronger local radio station overpowering the wireless FM transmitter in your overhead pod. If wireless reception is unsatisfactory, an optional wired relay box (Audiovox P/N SIRSWB) can be installed which will improve audio quality. Please contact the installer if this is the case with your product. -17- 128-7252A 17 of 35 AUX A/V Input The ADV200 will accept an audio/video input through the RCA jacks located on the side of the unit. The audio / video device could be a video game system, video camera, or other input device. Audio/Video Out The ADV200 provides an AV output for an optional video monitor(s). (Refer to page 6 of the Installation Guide for more details. ) This output will provide an A/V signal that duplicates the signal processed by the ADV200 to an additional monitor or video display. The audio signal can also be used to feed an AUX input on a vehicle radio if available. Please see your installer for more information. DVD Basics To get the optimum use out of the DVD player, make sure you read this section completely. Regional Coding Both the DVD player and disc are coded by region. [. . . ] The disc's software doesn't support the feature (e. g. , angles) 3. The feature is not available at the moment. You've requested a title or chapter number that is out of range. Picture is distorted · The disc might be damaged. Try another disc. · It is normal for some distortion to appear during forward or reverse scan. [. . . ]