User manual AUDIOVOX 892320

[. . . ] The product is intended to assist in safe driving and to allow the driver to have a broader rearview while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to the country and their local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle. [. . . ] Excessive force used before, during or after installation that results in a damaged or non-functional part shall void all warranties. Please follow the procedure from this user manual. Improper installation or modification of this product shall void all warranties. 2. 3. 4. 5. 3 Preface There is a blind spot that exists at the back of a vehicle while the vehicle is in reverse. Equipped with a camera, this rearview mirror/monitor ensures safety by providing the driver with a clear and wide image of the area behind the vehicle while it is in reverse. WARNING: Backing up vehicle Do not back up vehicle while watching the mirror/monitor screen. Always look in the direction of vehicle motion. Use the mirror/monitor as an aid in safety confirmation. The distance looks different in the monitor. The actual distance is shorter than it looks in the monitor. Packing list The Rear Observation System Package Model 892320 consists of the following items: 1. Installation Instructions (1) Mount the mirror/monitor onto the existing rearview mirror. a) Stick two adhesive foam backings on to the back of mirror in the two small rectangle indents. b) Take the two seven inch belts and slide them into the slots on the top rear of the mirror with grooved side of the belt facing down. Figure 1 c) Take the buckles and slide them into the lower slots on the rear of the mirror with the buckle facing down toward the seven-inch strap. Figure 2 NOTE: The large opened rectangle on the buckle will face away from the seven-inch strap. The three settings are 30 seconds, 150 seconds and 300 seconds. The vehicle operator can select to engage the navigation display timer by pressing SW 1 while the vehicle is going forward. The Navigation Display will appear for the preset time whenever the navigation system issues an audible voice command. 8 Figure 5 Figure 6 4. Controls and Indicators Figure 6 illustrates the controls and indicators of the 892320 rear view mirror: A: E: J: Rearview mirror Power indicator (Red when ignition is on) Switch 3 (see below) B: 4" LCD panel D: Brightness Control F: Volume Control H: Switch 2 (see below) K: Speakers C: Hands free Microphone G: Switch 1 (see below) 9 L: Infra- RED receiver for Navigation remote control M: 3-position switch for Navigation voice command display timer on rear of mirror (30 sec. , 150 sec. , 300 sec. ) N: 2-position switch for hands free microphone sensitivity High/Low select SW1, SW2 and SW 3: 1. Vehicle Reversing: SW 1: No function SW 2: No function SW 3: No function LCD automatically turns on Rearview camera image appears on the mirror 2. Vehicle driving: SW1: Turn on the Navigation display timer mode. When SW1 is pressed, the LED will turn yellow. The navigation image will appear for the preset time 30sec, 2. 5 minutes or 5 minutes. Once the preset time has expired, the LCD will return to its previous state. The navigation image will reappear with the next voice command prompt from the navigation computer. SW2: Turns the navigation screen image on and off. Press once to turn on the continuous Navigation display. Press again to turn off the Navigation display. [. . . ] When released the LCD will return back to its previous appearance. 11 Specifications General Power Supply Power Consumption Current Draw Video Input Audio Input Audio Power Output Operating Temperature Overall Dimension Display System Screen Brightness Contrast ratio Viewing Angle Resolution Video Format Display Format 4 " TFT Color LCD 250 nit 150:1 Top-10°, Bottom 30°, Left 45°, Right 45° 480×234 PAL/NTSC auto detect 4:3 12VDC <12W <500 mA 1Vp -p@ 75 Impedance <=1V 0. 5W × 2 (16O) -10°C to 60°C 11W×3. 75H×1. 25D inch 12 Maintenance Maintenance Your rearview mirror requires little care, however to maintain it in optimum condition follow the procedures below: 1. Keep your system away from excessive moisture, extreme heat or cold and magnetic fields. Do not place external devices or other objects on the top of the mirror. Occasionally clean the surface of the mirror with a soft cloth moistened with water, or a window cleaner. Troubleshooting Table 1 Rearview Mirror Symptoms The ON/OFF signal light <E> is not on after the car is started?Ensure that the parallel red and black line from the control box is connected properly. [. . . ]