User manual AUDIOVOX APS-155CH

[. . . ] Model APS-155CH Owner's Manual 3 Button Remote Security System with Stage Shock Sensor & Starter Disable FEATURES : w 2 Three Button Code Hopping RF Transmitters w Three Channel Code Learning Receiver (capable of accepting 4 transmitters) w Selectable Manual Override Mode w Remote Panic in all modes w Protected Valet w 7 Function LED -(Light Emitting Diode) - Arm / Disarm / Zone1, 2, 3 / Valet / Arming w Intrusion Alert with Memory w Audible Arm / Disarm / Defective Zone / Tamper Confirmation w Instant Siren Activation w Low Current Horn Output w Starter Disable ( Optional relay required ) w True Last Door Arming ( hardwire only ) w Defective Zone By - Pass w Hardwire or Voltage Sense Selectable w Active or Passive Arming Selectable w Programmable Auto Lock On / Off w Programmable Auto Unlock On / Off w Programmable Door Lock Pulse Duration 1 Second / 3. 5 Seconds/1 Sec L/ Dbl. U/L w Programmable Active or Passive Door Locks w User Programmable Permanent Chirp Delete w On Command RF Chirp Delete from Transmitter (Software Selectable) w 6 Tone Multi - Tone Siren w Additional Negative Trigger Input w RF Inhibit with ignition on w Parking Light Flasher w Plug In Dual Stage Shock Sensor OPTIONS : w Remote Trunk Release w Remote Keyless Entry w Multiple Vehicle Capable w Remote Starter w Remote Power Window Roll Up w Remote Garage Door Interface 128-6460 1 of 8 NOTE: Your system has the option of using a siren, the vehicle horn, or both for the sounding device. Where the siren is referenced below, the horn or both may in fact chirp, or beep. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid. [. . . ] o Doors Unlock - Optional NOTE: Chirps must be selected on to access this feature WHILE THE SYSTEM IS SOUNDING If during a triggered state, you wish to shut off the siren without disarming your security system, simply press and release any transmitter button other than the disarm button. This action will turn off the siren yet leave the vehicle fully armed and protected. This feature is particularly useful if you are aware of children playing near your vehicle that may accidently trigger your security system. In this case you can cancel the siren sounding INTRUSION WARNING SIGNALS This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt has occurred, the siren/horn will chirp 4 times and the parking lights will flash 3 times when disarming the system. Enter the vehicle, and observe the dash mounted LED to identify which zone was triggered. If the LED is flashing one time. . . pause. . . one time. . . pause. . . etc. , then an intrusion attempt was made to the shock sensor, or an accessory triggering device that may have been added to the system. If the LED is flashing two times. . . pause. . . two times. . . pause. . . etc. , then an intrusion attempt was made to a hood or trunk pin switch that was added to the system, or to a light activated entry point if the alarm was installed using the voltage sensing feature. If the LED is flashing three times. . . pause. . . three times. . . pause. . . etc. , then an intrusion attempt was made through one of the vehicle's doors. These intrusion warning indicators are stored in the system's memory, and will only be erased when the ignition key is turned on. VALET SWITCH The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed either by using your keychain transmitter, or by operating the manual override sequence. From the disarmed condition, turn the ignition key to the on position. Press and hold the valet push-button switch until the dash mounted LED, (Light Emitting Diode) turns on. The LED will remain on as long as the system is in valet mode. To return to normal operation, press and release the push button switch any time the ignition is on. Page 4 128-6460 4 of 8 NOTE: Always remember to return the system to the NON VALET mode, after servicing, to ensure that the vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM: USING THE VALET SWITCH MANUAL OVERRIDE Your Security System can be disarmed without the use of the keychain transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. If your system has been selected for Valet Switch manual override as indicated on the last page of this manual, to by-pass the alarm system. Turn the ignition key to the on position. Within 5 seconds, press and release the valet push button switch. [. . . ] 3) Within 5 seconds, turn the ignition switch off then on. 4) Within 5 seconds, press and release the push-button switch 1 time. 5) Turn the ignition switch off then on and start the vehicle. Note: If you have changed the programmed override code then substitute your new code tenths for step 2 above, and units for step 5 above. [. . . ]