User manual AUDIOVOX CP250

[. . . ] Pressing either side of the button for longer than 0. 5 second will activate the Seek Tuning function and cause the radio to search for stations automatically. The radio will seek the next station and stop at that frequency. Continuing to hold the button will cause the radio to tune rapidly in the selected direction until the button is released. 7 8 AUTO-STORE TUNING (AS) PRE-SET SCAN TUNING (PS) During radio operation, press this button momentarily to scan the five stations preset into the memories of the AM band or the ten pre-set memories of the FM bands. The unit will stop at each pre-set station for 5 seconds before continuing to the next pre-set station (the channel indicator number on the display panel will flash). [. . . ] When the cassette reaches the end of the side of the tape being played, the unit will automatically change direction of play as shown by the arrow indication on the display panel and play of the other side of the cassete will begin. NOTE: Observe cassette operation Cautions in Care and Maintenance section of this manual. bn FAST-FORWARD BUTTON (FF) bo Pushing the Fast-Forward button will cause the tape to move rapidly in the forward direction of play. To stop Fast-Forward movement, lightly push the Rewind Button until the Fast-Forward button disengages. Pushing the Rewind button will cause the tape to move rapidly in the reverse direction of play. To stop Rewind movement, lightly press the Fast-Forward button until the Rewind button disengages. bo REWINDBUTTON(REW) bp PROGRAMSELECTOR bn bn To manually reverse tape direction and play the other side of a cassette, lightly press both the Fast-Forward and Rewind buttons at the same time. The change of direction will be shown by the arrows on the LCD panel. bo bq EJECTBUTTON Tape playback is stopped and the cassette is ejected by pressing this button, which also has the function of switching over to radio operation. br MODE SELECTOR This button is used to select the audio source in play. During tape play, it can be used to change to radio play without ejecting the cassette. Similarly, it can then be used to go back to tape operation from radio play. NOTE: To prevent damage to cassette tape and/or mechanism, it is recommended that the cassette be ejected if it will not be played for prolonged periods. bs TIME/FREQUENCY SELECTOR (T/F) During radio operation, push this button to call the time display on the incorporated quartz clock. Pressing the button again will return to frequency display. During CD changer operation, push this button to call the time display or return to the disc and track number indications. Page 3 bt RE-SET BUTTON A re-set button is located on the front panel which must be activated by a pen tip or other thin object as it is recessed to prevent accidental engagement. The re-set circuitry is provided to protect the microprocessor circuitry and should only be activated under the following circumstances as it will erase the time and station preset memories. Upon initial installation after all wiring is completed. If there is a malfunction of any of the switches on the unit, pressing the re-set button may clear the system and return to normal operation. SETTING THE CLOCK 1. Switch the vehicle ignition "on" and the radio "on". 2. If the radio frequency is shown on the LCD panel , press the Time/Frequency momentarily so that the time display is shown. With the time display on the LCD panel, press and hold the Time/Frequency for approximately 2 seconds until the time display begins Selector (T/F) flashing. bs 4. Within 5 seconds of the display beginning to flash, press the Down Tuning( ) side of the button to adjust the hours, then the Up Tuning ( ) side of the button to adjust the minutes to the correct time. 7 5. After setting the correct time, press the Time/Frequency Selector (T/F) again or wait 5 seconds for the display to stop flashing. Page 4 CD CHANGER CONTROLS Built into this radio are controls to operate an optional 10-disc or 6-disc CD changer. Please check with your SPS/Audiovox or Prestige car stereo specialist for recommendations of the models that will work with this radio. Adjustment of audio functions (volume, tone, balance, and fader) operate in the same manner during CD play as they do for radio/cassette play. The following controls will operate the CD changer when it is installed and connected to this radio. Refer to the owner's manual included with the CD changer for instructions on the installation and correct loading and use of the CD magazine. bu MODESELECTOR(MODE) With the CD changer connected to the unit, this button is used to select CD changer operation. [. . . ] The Disc Scan mode will also be cancelled by activating any other disc function (Select, Cue, Review, Shuffle or Repeat). cq cq cr TRACK/DISC REPEAT (RPT) cr cq cs When the Repeat button is pressed, the "RPT" indication will appear on the display panel and play of the selected track will be continually repeated until the Track Repeat mode is cancelled by pressing the Repeat button again or by activating the Scan or Shuffle functions ("RPT" will disappear from the display panel). When the Repeat button is pressed and held longer than 2 seconds, the "DISC" and "RPT" indications will appear on the display panel and play of the selected disc will be continually repeated. The Disc Repeat mode can be cancelled by pressing the Repeat button again or by activating the Scan or Shuffle functions (" D ISC" and "RPT" will disappear from the display panel). cr cr cr cq cs When the Shuffle button is pressed, the "SHF" indication will appear on the display panel and the tracks on the disc will be played in a random, shuffled order. The Track Select button will also select tracks in the shuffled order instead of the normal progression. [. . . ]