User manual AUDIOVOX DT911

[. . . ] \ . , ;~ \ \-= GOM1\tlUNIGATIONS GORP. CORDLESS . 900MHz TELEPHONE DIGITAL ""' IMPORTANT REVIEW INSTRUCTIONS BEFORE OPERATION '-, -. ?, , -=-"'~. . . II '-"1=: , ~. . . ", . "". C'", :~"'~'. I:1:~C"c"i \, i"~. ~;;';\'Y &:~:liI. 1 . Auto hang up when returning the handset to the base cradle . Extension In Use indicator . 24 Bit Digital Security Code . DTMF and Pulse Dialing . Low Battery Detect and Warning indicator . . . HOLD, PAGE and MUTE . Hearing-Aid Compatible Receiver . Detachabl~ power supply. Nonvolatile storage of security code and memory dial memories . Programmable Ringer Types . Fully Digital Link between Handset and Base with ADPCM voice coding . Digitally-Scrambled Voice Communication . 20 location Programmable Memory for 20 Digit Phone Number . Special One- Touch memory keys for emergency or frequently dialled numbers . 10 Channel Operation with auto channel selection . Out-of-Range indication while the handset is in use or in standby mode . [. . . ] Do not use the telephone report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS 10 ~ dt911. p60 10 1998/6122, PM 06:59 ~~ III j1~, i ~~~f~~l'~ "' , ';- , , ;f~~~ ;, ". . '1;, 3. , =, , ~ Charging the handset batteries The handset of your AUDIOVOX DT911 cordless telephone is powered by a rechargeable battery pack. It charges automatically whenever the handset is in the base. You should charge the battery pack for 16 hours when you first receive your phone. You'll know the battery pack needs charging when: The phone emits a warning tone when you press the TALK key. Alternatively, if you have purchased a spare battery pack and it has been charging in the base unit, simply exchange the drained handset battery pack with the fully charged replacement battery pack from the base charger. if you have a fully charged battery pack in the Spare Battery charger and there is a power outage, you will still be able to place and receive calls for up to five hours. Replacing a Drained Handset bat- -::s:I~. tery The spare battery pack can also be used to replace a drained Handset battery pack to ensure uninterrupted use. Be sure to put the drained battery in the Spare Battery charger for recharging. Please note that the Spare battery pack recharges at a slower rate than a battery pack charging in he Handset. It takes 24 hours to fully charge a battery pack in the Spare Battery charger. 13 =fl dI911. p60 1998/6/22, PM 06:26 -"""'" ~ rf SETTING UP YOUR AUDIOVOX DT911 Choose an area near an electrical outlet and a telephone wall jack. AC POWER ADAPTOR Plug the AC power adaptor into an electrical outlet and the DC connector to the back of the base unit. J~ ~ [ ""1-, j. ; -, " 'r J i, :. . ~-. ; :1 TONE PULSE SELECTION c:) CHARGE THE HANDSET PACK BEFORE USE BATTERY 'f ; The battery pack rech'arges automatically whenever the handset is in the base unit. The battery pack must be charged for 16 hours before using your phone for the first time. , -(;))HANDSET RINGER The handset ringer is programmed ON as the factory default setting. Refer to PROGRAMMING THE RINGER on page # for more information. SErTINGTHETONE/PULSE SWITCH The TONE/PULSE switch is located on the bottom of the base unit and is factory set to TONE. If you have touch tone service, do not change the switch setting. If you have rotary {Pulse) service, set the switch to PULSE. + CONNECT TELEPHONE LINE CORD Plug one end of the telephone cord into a wall jack, and the other end into the back of the Base Unit. 14 5115198, 10'33 AM -@I ~ ~R~~~ After charging the battery pack, rotate the Base Unit antenna to an upright position. Pick up the Handset, making sure the Handset antenna is fully extended~ Now press T ALK , you should hear dial tone. If not, see 'IN CASE OF DIFFICULTY'. number card on = = = = FILL IN THE TELEPHONE NUMBER CARD , I ~ \\:;--d) c= --. :. ~ -::;-' ~ 15 =tl dt911. p60 IS 1998/6122, PM 06:28 . ~~ rF USING THE WALL MOUNT ADApTOR 1. Position the wall mount bracket on the base. line up the tabs on the wall mount adaptor with the holes on the bottom of the base (Figure 1 }. Snap the wall mount bracket firmly in place. Position the base so the mounting studs will fit into the holes on the bottom of the base. [. . . ] . Press PROG . The PHONE LED will flash quickly to indicate that the unit is in program mode. . Enter the memory location (00. . 20) you wish to store the number in. . Enter the phone number to be stored, up to a maximum of 20 digits. . Press MEM to store the number and exit program mode. [. . . ]