User manual AUDIOVOX DT941CI

[. . . ] COl\tl1\1UNICATIONS caRp. Cordless Telephone . 900MHz Digital . Caller ID . Digital Answering System , /--"' , " -, --. \ / \ I / I. - . . ~. . :. ~~~ , I \~;, \UDIO'. OX -. -, --~ ~ . . . . ) '0 ~ ---1 (0:. <C>~~'1:>-0 -c::::. :-c::::. -I <!0 <0 ~ ~ 0;;:1 IMPORTANT: REVIEW INSTRUCTIONS BEFORE OPERATION , :::::fi! . ;-c ~:', , 1. "'~. :. "';;;:. '?'. , , '" , )-:. :, "';:;. , :;. . , ~. ;~ . ~"fl:. ;, , '!!t. Page 1 2 3 4 7 9 12 14 15 16 17 18 19 21 22 22 22 22 22 23 INTRODUCTION Special Features Parts Check List FCC AND IC REGULATIONS IMPORTANT SAFETY INSTRUCTIONS REPLACING THE BATTERY PACK GETTING STARTED WALL MOUNTING EXAMPLES OF THE HANDSET DISPLAY THE HANDSET LAYOUT THE BASE UNIT LAYOUT , . [. . . ] , If you make a mistake when dialing, pres. 12m to hang up, then press the ~ key to get the dial tone again. Disconnecting To end a call, either place the handset back in the base, or press (Qffl on the handset. Answering Calls When the Handset rin~ss any key other than (Qff), lMUTEJ or the VOLUME keys to answer your call. Volume Controls The volume controls for the handset are located on the side of the unit. Press the A (up) "or '\1 (down) keys to increase or decrease the volume. Holding either key down will continuously change the volume setting. The earpiece volume level indicator on the dispaly will change accordingly. There are four volume levels. 21 + . Press @QI§) while phone is ringing to disable the ringer for the duration of the call. . Press ~ to place an activecall on hold. PAGE Handset Locator J . ~e from the Base Unit press l~J . . The Handset will display BASE PAGING HANDSET. . To cancel the pager either press ~~ on the Base Unit, or press ~ on the Handset. -i DT94102. p65 21 6/24/98, 12:20 PM II rF Call Waiting CALL WAITING is a subscription service, available from most local telephone service providers. While you are on a call, you will hear an alert signal, warning that a second caller is trying to reach you. . . :. If you subscribe to this service linked with CALLER ID (CID), the name and/ or phone number of the second caller can be displayed on the Handset immediately after hearing the CALL WAITING alert. Switching calls using FLASH . To switch over to the new call, press the@:!5]key; the first call is put on hold. . To switch back to the first call, press the @:!5] key again. First, dial the call normally. Then activate the Temporary Tone feature by pressing TONE (the * key). You can then press the numbers or symbols you need, and your phqne will send the proper signals. To end the call, press @) or place the handset back in the base. The phone will automatically go back to rotary (PULSE) service. I -(ft- -fJj>- Programming Ringer . The handset ringer is capable of four different types of ringer tones. The following sections detail how to select different ringer types and how to turn off the handset ringer. Temporary Tone If you have rotary (PULSE) telephone service (TONE/PULSE switch is set to PULSE), this feature allows you to temporarily switch to TONE dialing for such purposes as remote access to answering machines, bank-by-phone services, use of calling cards and other special services. 22 ~ --, -, DT94102. p65 22 6/24/98. [. . . ] Try moving the appliance or the base unit to another outlet. ringer activated. To set the ringer, see . PROGRAMMING THE RINGER. . . Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack. . You may have too mahy extension phones on your telephone line to allow all of them to ring. [. . . ]