User manual AUDIOVOX LCM1511WTV

[. . . ] Interface Cable to Tuner AUX Page 1 LCD, Tuner Pack, IR Remote Control TV/CATV/ AV1/AV2 OSD MUTE COLOR CONTRAST FM MUTE POWER BRIGHTNESS AUTO PROGRAM FM SELECT/CHANNEL VOLUME ADJUST BATTERY AAA Size 1. 5V x 2 Remote Controller POWER ON/OFF CHANNEL SELECT VOLUME ADJUST +/COLOR COLOR Page 2 TV/AV MENU MUTE SPKR ON/OFF CONTRAST CONTRAST BRIGHT BRIGHTEN 2. Feature Function, IR Remote 2-1 Power Pointing the remote towards the IR eye on the LCD, press and hold the POWER On/Off button on the remote controller unit until it turns on the system. Repeat this procedure to turn off system. Power On- The LCD monitor will light up, and the green power light on the front panel will be ON. [. . . ] NTSC - M / PAL - BGHI Color System selection 2. PAL 4. 43 / NTSC 4. 43: 50Hz on AV mode 3. PAL 4. 43 / SECAM (-)Off Select + Menu On(+) Reset to factory setting Press Select First Reset- Default PWROn/Off Page 5 4. Feature Functions 4-1 No Signal Detection The monitor will detect signal input automatically. If the signal source is OFF or removed, there is a" " icon that will appear and blink on the upper right corner of the screen that means "No Signal Input". The system will go to power saving mode when there is no signal input for 1 minute. 4-2 Auto Memory Function All of the functions adjustments, will be saved automatically. If you want to change back to the default setting, please use in the OSD menu to reset everything back to the factory setting. 4-3 PC VGA Multi-Sync Mode All available modes are listed below: Display Mode 350 400 Text VGA Resolution 640 x 350 @ 85 640 x 400 @ 85 720 x 400 @ 70 720 x 400 @ 85 640 x 480 @ 60 640 x 480 @ 73 640 x 480 @ 75 640 x 480 @ 85 800 x 600 @ 56 800 x 600 @ 60 800 x 600 @ 72 800 x 600 @ 75 800 x 600 @ 85 1024 x 768 @ 60 1024 x 768 @ 70 1024 x 768 @ 75 1024 x 768 @ 85 H. Frequency (KHz) 37. 861 37. 861 31. 5 37. 927 31. 469 37. 861 37. 5 43. 269 35. 156 37. 879 48. 077 46. 875 53. 674 48. 363 56. 476 60. 023 68. 677 V. Frequency (Hz) 85. 098 85. 08 70 85. 039 59. 94 72. 809 75 85. 008 56. 25 60. 317 72 75 85. 061 60. 004 70. 069 75. 029 84. 997 Dot Clock (MHz) 31. 5 31. 5 28 35. 5 25. 175 31. 5 31. 5 36 36 40 50 49. 5 56. 25 65 75 78. 75 94. 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 SVGA XGA NOTE: 15. 1" Panel resolution is up to XGA. Page 6 5. Tuner Functions: (Performed only by IR Remote) 5-1 Power Press and hold the POWER On/Off button on the IR remote controller unit the system turns ON. Repeat this procedure to turn the power off. Power-On: The LCD monitor will light up, and the green LED on the front panel of the monitor will be On. The On Screen Display (OSD) will show the last position where you turned the unit Off. 38, then turn the power OFF, the next time you power up the screen will display CATV Ch. Turning OFF power: The monitor screen will be dark and the indicator will turn orange. 5-2 TV/CATV/AV1/AV2 Mode Selection Use the TV/CATV button to switch between TV/CATV/AV1/AV2. System US-181 (NTSC) PAL/DK PAL/BG PAL/AI JAPAN Air Cable TV Channels 2~69 Cable TV Channels 1~57 Cable TV Channels 2 ~69 Cable TV Channels 21 ~ 69 Cable TV Channels 1 ~ 62 CATV Cable TV Channels 2 ~ 125 Cable TV Channels 1 ~ 63 Cable TV Channels 1 ~ 57 Cable TV Channels 1 ~ 53 Cable TV Channels 1 ~ 63 Mode source Description AV1 External Audio and Video Input 1 AV2 External Audio and Video Input 2 NOTE: First press of the TV/AV button, system will display status only. Press it again to perform switching function. 5-3 TV/CATV Channel Programming Use AUTO PROG. button to memorize the channels in CATV or VHF/UHF. Button, the tuner will start to scan all of the available channels and put the active ones into memory. [. . . ] 3) Use the monitor's metal frame as a template to drill holes and cut opening. 4) To properly align holes- place monitor bracket level on wall. Mark all hole locations and outer edge of flange. 5) Pre-drill larger holes using 5/16" drill bit. [. . . ]