User manual AUTOTEK 66

[. . . ] Radio wave transfers almost in straight routine in 2. 4GHz, please make sure there is no any obstacle when you are operating the product. The antenna tube should point at the controlled model to ensure efficient control, and keep conductive materials away from receiver and transmitter. If there is prang, collision, welter and other accidents when operating, please test all the things before next operating. Always keep electrical components away from small children. [. . . ] If you must fly in wet weather during a contest, be sure to cover your transmitter with a plastic bag or waterproof barrier. Never fly if lightning is expected. 3 Part 1 66 2. 4GHz Remote Controller System 66 2. 4GHz REMOTE CONTROLLER SYSTEM UNITS ADVANCED ELECTRONICDEVICE, AND FEATURES WIDE USE. It can support multi-users and multi-equipmensimultaneously, and features quick response, high precision, and strong capability for antijamming. 66 2. 4GHz R/C system supports one transmitter and several receivers, and makes ipossible that single radio can control several models simultaneously. 66 2. 4GHz R/C system supports different brand gyro. 66 2. 4GHz R/C system reacts quickly and precisely. 2) Hold the 'BIND button' of transmitter, then turn it (keep holding), the RF LED of transmitter will flash fast. 3) After about half second, binding will finish, the LED of receiver will shine twice slowly, then enter working mode. 4) Release the 'BIND button' of transmitter, the RF LED will keep light, which indicates it is in working mode. on 4 1. Mounting of Receiver Installation position shall follow these conditions: 1. Keep the receiver away from engine, motor, ESC, battery, and other metal parts. 2. The antenna can not be covered by metal, carbon material or the other electronic conduction material. Keep the antenna in 90 degrees with installed frame or bottom plate, it means that try to keep the antenna visible, see the graph below: The receiver has been plugged bind line Bind button on the back of transmitter Bind button of transmitter Notice: 1)66 2. 4GHz remote controller system sustain multiple receivers operation and long-distance scaning, so please make sure there's only your radio scaning. Stick Adjusting Tighten the screw when finishing adusting. In HELI mode, it is used to switch NORMAL mode and IDLE mode. it is used to control dual rate of aileron, elevator and rudder. 5 System Setting In AERO mode, it controls channel5. See section-7 See section-6. 10 and There are three items "S1", "S2", "S3" and "S4". 3 Batteries Charging S1. Model choice Support seven models, see Section-10 S3. Low voltage gate Set the voltage gate of low battery warning 10 11 6. 4 Dual Rate Setting 6. 6 Gyro Sensitivity Adjusting The sensitivity value can be set from -100~+100. When it is greater than 0, the gyro is in headlock mode, when the value is lesser than or equal to 0, the gyro is in non-lock mode. The default value is G1=G2=0. 6. 7 Throttle Curve Setting at the same time 6. 5 Throttle Holding Setting be from will not at the same time 12 13 6. 7 Throttle Curve Setting are are * Signal and Curve 6. 8 Pitch Curve Setting at the same time 6. 9 Swash Mixture Setting from the same time are 14 15 There are six settings in V-tail mode. To enter setting, press UP and DN at the same time special times, and five operations beyond are the same as in HELI mode. You can press INC and DEC at the same time to exit setting and return to using mode. 6. 10 Aux channel setting When in HELI mode, the GEAR switch controls channel 7, and the AUX channel. There are two items in AUX channel setting, A1 and A2, control the signal of AUX channel when GEAR switch in different position. To enter this setting, turn on transmitter, then press UP and DN at the same time ten times, you will see "A1 xxx" like CHART14. CHART14 - AUX channel Press UP or DN will change setting from A1 to A2. [. . . ] If the Idle switch on when power on, the transmitter will block in warning status. You will see "IdLE" in panel and hear continuously beep till you switch Idle to off. CHART 25 ­ PPM status Notice: when the transmitter in PPM status, the RF module stops working and RF led will off, then the receiver will lost signal if it was on. CHART22 - Idle warning 13 Down timer 66 7CH has a down timer relate to throttle. When in normal using status, press DEC and DN at the same time to enter down timer. The default value is five minutes, like CHART22. You can press INC or DEC to change the value. When you push throttle stick up, the timer will run from the value you set to zero. [. . . ]