User manual AVIOM A-16CS

[. . . ] A-16R Personal Mixer A-16CS Control Surface For Use With Aviom Monitor Mixing and Distributed Audio Network Products User Guide Information in this document is subject to change. 1. 04 06/06 Printed in USA Part Number 9310 1003 0004 Aviom, Inc. 1157 Phoenixville Pike - Suite 201 West Chester, PA 19380-4254 USA +1 610-738-9005 (voice) +1 610-738-9950 (fax) www. aviom. com Aviom and the Aviom logo are trademarks of Aviom, Inc. A-Net and the A-Net logo are trademarks of Aviom, Inc. WARNING! ! TO REDUCE THE DANGER OF ELECTRICAL SHOCK DO NOT REMOVE COVERS. [. . . ] · Select a Channel that is not currently part of an existing Group. · Press the GRoup button to enter Group Mode. · Double-click any Channels that you want to add to the new Group. · To save the Group, press the GRoup button again to exit Group Mode. Shortcut: While in the Group edit mode, you can start the process of creating a new Group while editing an existing Group. To do this, · Press a Channel button that is not already part of the current Group being edited. · Double-click Channels to add them to a new Group. · Create a third Group by following the same procedure. · Exit the Group edit mode to save the Groups. If you try to create more than three Groups, the interface will automatically select one of the existing Groups when you enter Group edit mode. You have the option at this point to edit an existing Group or clear Channels that are part of one of the other existing Groups. AviomA-16RandA-16CSUserGuide Note: A Channel that is already part of one Group cannot be part of any other Group. Making Changes to a Group Once you have created a Group, you can edit it in a number of ways. You can add or delete Channels from the Group, and change individual Channel volume, mute and pan settings. To change a Group, start by selecting a Channel that is already part of a Group. All Channel LEDs that are part of the Group will light. Press the GRoup button to enter the editing mode. Then, follow the specific directions below. Changing Channel Volumes Within a Group While editing a Group, you'll notice that one LED in each Group is lit solid while the other LEDs are flashing. The solid LED indicates the Channel currently selected for editing. You can change its volume and panning without affecting other components of the Group. The changes you make to volume and pan affect only the selected Channel, allowing you to change the relative balance of the individual components of your Group. To select a different Channel in a Group for editing, press one of the flashing LEDs (don't double-click it). The new selection will light its LED solid, while the previously selected Channel will start to flash. Remember, volume and pan changes only affect the Channel whose LED is lit solid. Removing Channels From a Group To remove a Channel from a Group, simply double-click the Channel that you want to remove while in the Group edit mode. [. . . ] | Preset ID 0001 0000 0001 1111 Preset Data Preset Checksum . . . 0001 nnnn 0001 nnnn Preset Trailer Padding EOX 0100 0000 . . . 1111 0111 * - Valid preset range 0-15 AviomA-16RandA-16CSUserGuide 5. MIDI Current Preset Detail Listed below is a more detailed picture of the "MIDI Current Preset" message as implemented on the A-16R. SOX Manufacturer's ID 1111 0000 0000 0000 0000 0001 0100 0101 (F0H) (00H) (01H) (45H) (00H) (00H) (00H) (01H) (00H) (00H) (00H) (00H) (00H) (00H) (10H) (10H) . . . - Start of Exclusive Aviom Manufacturer's ID Byte 1 Aviom Manufacturer's ID Byte 2 Aviom Manufacturer's ID Byte 3 (A16 Family) (A-16R Product) (expansion) Message Type = MIDI_ CURRENT_PRESET_MSG Message Descriptor Byte 1 (expansion) Message Descriptor Byte 2 (expansion) Message Descriptor Byte 3 (expansion) Message Descriptor Byte 4 (expansion) Message Descriptor Byte 5 (expansion) Message Descriptor Byte 6 (expansion) Unused Unused 112 consecutive bytes containing info for one preset Nibblized Preset Data Checksum (MSB) Nibblized Preset Data Checksum (LSB) Family ID Product ID Device ID Msg. [. . . ]