User manual AVIOM AVIOM16-O-Y1

[. . . ] AVIOM16/O-Y1 A-Net OUtpUt CArd fOr YAmAhA diGitAl mixers AVIOM16/o-Y1 Mode Dn/Up - Aviom Up/Dn - 16 ch Up/Up - 8 ch Dn/Dn - Test 1 2 3 4 5 6 7 8 9 10 Stereo Link A-Net Out Made in USA User GUide A-Net and the A-Net logo are trademarks of Aviom, Inc. Aviom and the Aviom logo are trademarks of Aviom, Inc. All other trademarks are property of their respective owners. Information in this document is subject to change. 1. 01 ! Warning Failure to observe the following warnings may lead to risk of serious injury from fire or electric shock. Before installing the card, you must refer to the owner's manual of the host device or to the Yamaha website to verify that your host device supports this card, and to verify the number of cards that can be installed in combination with other Yamaha or third-party cards. [. . . ] To remove the cable, press on the metal release tab at the top of the panelmounted EtherCon jack and pull the connector outward. Y1 Card Components AVIOM16/o-Y1 Mode Dn/Up - Aviom Up/Dn - 16 ch Up/Up - 8 ch Dn/Dn - Test 1 2 3 4 5 6 7 8 9 10 Stereo Link A-Net Out Made in USA 1 2 3 4 5 1 2 3 4 5 Thumb Screws DIP Switch - Stereo Link DIP Switch - Mode Selection A-Net Output Locking EtherCon RJ45 connector with release tab Installing the Y1 Card The Y1 card can be used in any expansion slot in the Yamaha mixing console. The number of available expansion slots varies with each model. In the Yamaha user interface, the expansions slots are identified by number, starting with "1". Multi-pin connector Align sides of Y1 card with guides in the expansion slot. Thumb screws To install the Y1 card: · Start with the power to the Yamaha mixing console off. · Remove the mixer's power cord from the wall receptacle. · Remove the cover plate on the rear of the Yamaha expansion port to expose the expansion connections. · Remove the Y1 card from its protective anti-static sleeve. · Slide the Y1 card into place, aligning the sides of the card with the support guides in the expansion slot. · Press the Y1 card firmly in place to attach the multipin card connectors on the Y1 card and Yamaha mixer. · Attach the Y1 card permanently by tightening the two thumb screws on the rear panel of the Y1 card. Note: Aviom suggests using Category 5e (or better) cables when making A-Net connections. DIP Switch The 10-position DIP switch provides two separate functions. The first eight switches are used for controlling the stereo link status of the eight possible audio channel pairs. The last two switches (labeled 9 and 10) provide mode selection control for the Y1 card operation. Dn/Up - Aviom Up/Dn - 16 ch Up/Up - 8 ch Dn/Dn - Test AVIOM1 Mode Mode 1 2 31 42 5 3 6 4 57 6 8 7 9 8 10 9 10 Stereo Stereo Link Link A-Net Out The DIP switch handles shown in the diagrams in this document are illustrated in white. (In the diagram above, for example, switch #10 is in the up position. ) ! Made Stereo Link Switches Positions 1 to 8 of the DIP switch are used for the stereo link function. Stereo linking is possible when using Aviom's Pro16 Personal Mixers for stereo monitoring. Each switch controls a pair of channels; see the list below. When the switch is set to the "On" position (down), the channels are linked as a stereo pair. If the switch is in the "Off " (up) position, the channels are not linked. Stereo link changes can be made at any time. All connected A-Net devices will instantly update and reflect the change. Compatible A-Net devices that do not respond to stereo linking will not be affected by changes to the link status. The DIP switch 1 to 8 definitions are as follows: · Switch 1 - controls channels 1 and 2 · Switch 2 - controls channels 3 and 4 · Switch 3 - controls channels 5 and 6 · Switch 4 - controls channels 7 and 8 · Switch 5 - controls channels 9 and 10 · Switch 6 - controls channels 11 and 12 · Switch 7 - controls channels 13 and 14 · Switch 8 - controls channels 15 and 16 Mode 1 2 3 4 5 6 7 8 9 10 Stereo Link The example above shows a configuration where channel pairs 3-4, 13-14, and 15-16 are set for stereo operation. Mode Select Switches Positions 9 and 10 of the DIP switch are used for card mode selection. There are four possible switch combinations; three operational modes and one test mode are provided. [. . . ] Another 500 feet (150 meters) of cable can then be added. This process can be repeated as many times as required to extend cables. In fact, any Pro16 A-Net device can be used as a signal repeater. For long distance applications, fiber optic cable can be used to span distances up to 50 miles (80km) with the use of devices called media converters. [. . . ]