User manual AVIOSYS IP KAMERA 9070-IR V1.2

[. . . ] IP Kamera 9070-IR User Manual Release Date: 10/20/2009 Manual Version: 1. 2 - 1Ref#90020326K0709 Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. IP Kamera 9070-IR was designed for outdoor/ indoor. Please use the power adapter provided by the dealer, the manufacturer is not responsibility for the possible damage from using power adapters. Do not shake the IP Kamera 9070-IR in any fashion 5. [. . . ] Quick Zoom In: Quick zoom in is used to quickly zoom into the maximum zoom of the picture. To use this function on the picture double click the left mouse. Quick Zoom Out: Quick zoom out is used to quickly zoom into the maximum zoom of the picture. To use this function on the picture double click the right mouse. Motion Detection Motion Detection: The motion detection icon will display when motion has been detected. This setting must be activated in the application section No Motion Detected Motion Detected Active Record Active Record: Active record will show up when the device is actively recording. Active recording functions like motion detection, scheduler, or an alarm will set off this automatic recording. - 21Ref#90020326K0709 Automatic Recording Inactivated Automatic Recording Activated Record Record: The record button on the 9070-IR when pressed will record the live video feed and save the video into the computer viewing. To record follow the following steps: 1. ) Click on the record button 2. ) Then select the designated folder to store the file. Then hit okay. 3. ) Once the folder has been selected the device will start to record. To stop recording click on the red icon and it will return to the original state. Note: Remember VLC codec is required to play the video files that are recorded Snapshot Snapshot: The snapshot function, creates a easy way take pictures of the current view in the IP Kamera 9070. To setup the snapshot destination folder: 1. ) Click on the Application link on the bottom menu 2. ) Then select Snapshot path 3. ) In here browse for the location where snapshot pictures will be stored. By default the snapshot path will be in C:/ - 22Ref#90020326K0709 To use the snapshot function: 1. ) Click on the snapshot button 2. ) In explorer go to the selected path and the files will be created there. Image The image section changes the Image settings for the device and tunes the image of the IP Kamera 9070-IR Image Settings The Image settings section changes the video settings and the Name of the Kamera. Camera Name: Select a camera name for the device and then hit submit Video Codec: \ - 23Ref#90020326K0709 Resolution: Resolution (MPEG4+MPEG4+JPEG): M4:720P, M4:CIF, JPG:352 (MPEG4+JPEG): M4:VGA, JPEG:VGA (MPEG4+JPEG): M4:720, JPEG:352 (MEG4+MPEG4): M4:720, M4:CIF (Single MPEG4): M4:720 Color System: Select the broadcasting color system that pertains the country. NTSC/60Hz PAL/50Hz Rate Control: Select the most suitable Bit Rate Control. CVBR: Constrained Variable Bit Rate CBR: Constant Bit Rate M-JPEG Settings: The available Quality settings and FPS for the M-JPEG settings are shown below M-JPEG Quality Settings High Medium Low M-JPEG Frame Rate Settings 30 FPS 15 FPS 7. 5 FPS 3 FPS 1 FPS MPEG4-2 Bit Rate: Select a value from 64~8000. FPS: Select a FPS from 15fps or 7. 5fps MPEG4-1 Bit Rate: Select a value from 64~8000. FPS: Select a FPS from 30fps, 15fps, or 7. 5fps Enable EPTZ: The EPTZ on the IP Kamera 9070-IR a virtual EPTZ function. This function allows the user to control the video on the Live Video mode by moving left or right, zooming in and zooming out. To use the EPTZ mode: 1. ) Enable the EPTZ function and then hit the submit button. 2. ) Click on Live Video Mode 3. ) Click on EPTZ-Set and a new control window will pop out. - 24Ref#90020326K0709 From here control the live view Zoom Function and direction. Also once EPTZ is enabled, in the Live View Screen buttons will appear on the bottom with the pan, tilt, and zoom button Note: PTZ is only available in the mode below. When PTZ is enabled, it will automatically jump into that mode. Tune Image The tune image settings section controls and tunes the picture quality of the image. Keep in mind, the quality of the picture will also be affected by the quality of the lens that is being used. White Balance: Select from the following options auto, indoor, or outdoor Day and Night: Select the mode Day or Night TV Output: Select the mode enable or disable to output to a T. V - 25Ref#90020326K0709 Binning / Skipping mode: Binning enables low light-light performance. Select Binning, Skipping, 4x Binning mode (default is Binning). During BLC (Backlight control): Here Backlight control can be turned on or turned off. [. . . ] *Note: IP Server must be enabled on the device's webpage. Find MAC Address in LAN Using IPEdit - 48Ref#90020326K0709 1. ) In IPEdit, highlight the device that is being used. On the right side of IPEdit the MAC Address for CNT will be listed. *Note: Make sure when typing in the MAC address to leave out the ":" Find MAC Address in WAN Using IPService on IPEdit 1. ) Find the MAC Address through the internet, Open IPEdit and hit the connect button on IP Service. [. . . ]