User manual AXIS BTA 210D

[. . . ] BTA2100(D) BTA210(D) USER MANUAL BTA Series File: ER-BTA-144-05-10 btA0009 GB 2 Contents: USER MANUAL __________________________________________________________________________________________________________________ 1. General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Completeness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Safety rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4. [. . . ] Weighing result is displayed in various formats, depending on reference mass value. For reference mass values between 0÷3, 5% of scale capacity, format of weighing result is 100. 0, for values between 3, 5÷35% it is 100. 00 and above 35% - 100. 000. The function has the following options: - PEr oFF ­ switch the function off, - PEr on ­ set current indication as 100%, show indications in %, - out ­ exit without changes. PEr Err message informs that reference mass is less than 0, 5Min or was not defined. When the scale shows weighing result in percent, T key works as usual. 0. 00 g 19. 07 g MENU PErCEnt T PEr oFF PEr on 50% T 100. 00% 50. 00% USER MANUAL 25 __________________________________________________________________________________________________________________ 15. 6. Function for summing recipe ingredients (rECIPE) 0. 00 g rECIPE rEC oFF rEC on T MENU T A The function allows for separate weighing of several ingredients in one container with the possibility of reading current sum of all weighed ingredients. The function includes the following options: -rEC oFF ­ leave the function with the possibility of read sum mass, -rEC on ­ start recipe weighing, -rEC Con ­ continue previous recipe, -out ­ exit without changes. o 10. 01g T B o 0. 00g When proceeding with recipe, successive ingredients (A, B, C, etc. ) are weighed each time starting from zero indication, which is obtained after scale taring. T o 10. 02g C o 0. 00g MENU If several ingredients are weighed, their sum mass can be read (despite several taring). For this purpose use rEC oFF option. o 10. 03g rECIPE A+ B+ C rEC oFF 30. 06g T T Comments: o indicator on the left side of scale display shows rECIPE function is active. SUM indicator shown when rEC oFF option is used, disappears after using T key. 26 USER MANUAL __________________________________________________________________________________________________________________ 15. 7. Function for calibration with external weight (CALIbr) Calibration with external weight should be performed if scale accuracy is not satisfactory. Calibration weight stated in technical data table for the scale (or of better accuracy) should be used then. Operations sequence: Press MENU key to display user functions, shown one by one in loop. Press T key when CALIbr function appears. The following options will be displayed: -CAL on ­ calibration with external recommanded value weight (see technical data). -CAL StP ­ calibration with external weight, confirmation of next steps - MENU key, -CAL Pt ­ calibration with external weight other value, out ­ leave without changes Press T key when CAL on option appears. Wait for writing zero to the scale. 0. 00g CALIbr CAL oFF MENU T . . . CAL on - CAL - T 0. 00g m LOAD m 0. 00g When LOAD message appears put calibration weight on the pan. Wait until internal calibration is zero indication is finished displayed. Attention: CAL StP option generates commu-nications Press Menu. USER MANUAL 27 __________________________________________________________________________________________________________________ 15. 8. Label choosing function (LAbEL) This function is used in scale with ELTRON (Port-1) data protocol. This protocol enables label printout with actual scale indication and chosen data from PrInt special function (variable data), for example date and time. Other data, for example company address, product name, barcode can appear on label as a constant text. Label patterns with number (4 digit) used by user should be saved in scale memory according to printer manual. Label pattern choice is made by inscribing label number using LAbEL function. [. . . ] Following threshold options are displayed: - SEt-0 - start the function with the excess signalisation, - SEt-1 - set lower threshold value, - SEt-2 - set upper threshold value, - SEt-3 - set zero excess signalisation, Using T key choose option SEt1. Set the lower and the upper threshold values with the following keys: - digit increase, - decimal point, T - next digit, MENU - end. Next choose option SEt-2 and write upper threshold value. When necessary, use SEt-3 option to set the value underneath which the sign MIN isn't displayed. [. . . ]