User manual B&K CT610

[. . . ] B & K Components, Ltd. User Manual CT610 CT310 CT602 CT600 CT300 Multi-Zone Audio/Video Receivers 13226 0905 COMPLETE USER MANUAL - CT RECEIVER © 2005 B & K Components, Ltd. All rights reserved. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from B & K Components, Ltd. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. [. . . ] Once the codes have been assigned, functions like lowering the volume in Junior's room from the Kitchen keypad is possible. Code-Sets can also control a group of zones (such as upstairs or party modes) or control the whole house (all zones) using Code-Set 0-0-0. In a basic default system, all keypads are pre-programmed with Code-Set 1-2-8. The CT Receiver monitors which one of the six Zone Control terminals the IR command was received from and responds only in that zone. Thus, as long as each keypad is hard wired to the correct Zone Control terminal, all keypads can be programmed identically using code 1-2-8. However, the user can be provided with powerful convenience features by utilizing discrete Code-Sets to enable any keypad to control any zone, any group of zones or the whole house. The front panel will not respond to Code Set 1-2-8 received from a remote control. B & K created 128 different sets of the same CT Receiver commands. These commands will also work with B & K home theater units assigned to the same code set. The primary commands are as follows: Power State ZONE POWER ON POWER OFF Tone BASS BASS + TREBLE TREBLE + LOUDNESS Input Sources SOURCE + SOURCE VIDEO SOURCE + DEDICATED IN INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT 6 INPUT 7 INPUT 8 INPUT 9 TUNER Tuner AM FM BAND TOGGLE TUNE TUNE + STATION STATION + Volume MUTE ON MUTE OFF STEREO/MONO MUTE (TOGGLE) MASTER VOL+ MASTER VOL- *This list is not a complete list of commands. For a complete list please refer to page 7 of this manual. Each code-set differs from the next only in the initial IR code identification or prefix, i. e. This way a CT Receiver zone can be setup to recognize an intended command no matter what Zone Control terminal the command is received from. Thus, any zone can control any other zone (or group of zones) by programming a remote control or a keypad with the appropriate set or sets of codes from the following choices: Code Code Code Code Set Set Set Set 000 Controls ALL zones simultaneously. (Multi Zone and Home Theater) 001-127 Can be utilized for group or independent zone operation. (Discrete) 128 Controls only the zone it is connected to or received from. (Hardware Specific) 999 Controls a set of B & K ALL commands (Multi Zone and Home Theater) S IMPLY B ETTER! B&K 42 Groups / Code Sets / Zones - Tab 2 You can program a maximum of 18 groups for each CT Receiver labeled a - r for your reference only. Group 0 cannot be changed, it is pre-programmed with code-set 0-0-0 (controls ALL CT Zones). Each group can control any or all zones within one CT Receiver. If multiple CT's are going to utilize the same code for a group spread across multiple CT Receivers, that code-set must be programmed into each CT receiver. 1. Code-Sets: For each group, assign a code-set between 001 and 127. B & K recommends the following: in the first CT610 assign Code-Sets 011 to 016 to each individual zone A-F. When working with a system with more than one CT, assign code sets 021 to 026 to the second CT, 031 to 036 to the third and so on. 3. [. . . ] products is NOT VALID if the products have been purchased from an unauthorized dealer or an E-tailer or if the original factory serial number has been removed, defaced or replaced in any way. sells its products through authorized dealers in order to insure that consumers obtain proper dealer service and support. Buying from an authorized B & K Components, Ltd. dealer insures that you have a FACTORY WARRANTY on your B & K Components, Ltd. [. . . ]