User manual B&K ST1400M II

[. . . ] Do not stack anything on top of the amplifier (preamplifier, processor, source. . . etc. ). Leave at least 2-3 inches clearance from the top of the amplifier to the next shelf, component, etc. , to ensure proper ventilation. * If you are at all unsure of what the speaker `ratings' are, contact your dealer. Page 2 The ST1400M series II is a compact, very efficient, single channel power amplifier. It is designed to be used in all types of audio or audio/video systems. The ST1400M series II utilizes high quality electronic circuitry to achieve an environment wherein a detailed, transparent, and highly musical sound can be realized. The high quality parts complement include state-of-the-art solid state devices, 1% metal film resistors, computer grade electrolytic power supply capacitors, and a high capacity toroidal transformer. [. . . ] They are designed to accept a banana-type plug or spade lug connector (shown below) and are color coded for easy identification. The red (+) post should always be connected to the speakers (+) jack. The black (-) post should always be connected to the speakers (-) jack. Spade connector Banana jack Here is a typical amplifier setup: The ST1400M series II amplifier has two sets of binding posts on it. They are paralleled inside the amplifier. The amplifier comes standard with a right and left speaker output. The left output is used for normal operation, but you can use the right output to connect to another left channel speaker. Page 7 Unbalanced - RCA type connectors accept line input from the preamplifier's unbalanced output connectors. There are two input connectors, that may be used to connect the amplifier to the preamplifier. RCA cable connector - Operation - For unbalanced operation, ensure the balanced switch between the balanced inputs on the rear of the amplifier is in the `off' (out) position. If the amplifier does not have balanced inputs then it is always in unbalanced mode. XLR type connectors accept line input from the preamplifier's balanced output connectors. The ST1400M series II has balanced line inputs. Balanced - Balanced cable connector - Operation - For balanced operation, ensure the balanced switch between the balanced inputs on the rear of the amplifier is in the `on' (in) position. Here is a typical input setup: Page 8 There will most likely be a number of cables involved in the installation of your home entertainment system. Pre-planning is essential in order to maximize system efficiency. We recommend the following as a means of helping you reach that goal: Make a diagram of your proposed system by laying out the relative location of each component in the system. Then lay out the proposed cable runs between them. Number each cable and record its length on the diagram for future reference. Cable runs are critical in that they must be kept away from sources of power radiation (amplifiers, power cords, heaters, etc. . . ). For the sake of safety, they should also be kept out of traffic areas. The process of optimizing the system will include the type of cable, the length of the run, and the obstructions it must deal with along its run. Your dealer can advise you on the products available and their relative merits. If building custom length audio cables is not your strength, your dealer should be able to help you with that as well. When possible, use a separate AC power line for the amplifier, one that is not shared by any other component in the system of any other house hold component. Before doing anything, ensure that the power switch on the amplifier's front panel is in the `off' position. Again, it is recommended that you locate a separate AC power outlet for the amplifier, one that is shared by any other audio component in the system or any other house hold component. This will eliminate the possibility of the amplifier `modulating' the power being supplied to the component and compromising the signal originating from that component. [. . . ] No agent, representative, dealer or employee of B&K has the authority to increase or alter the obligations or terms of this warranty. B&K Components Ltd. No equipment may be returned to B&K Components Ltd. Should you find it necessary to return equipment to B&K, for any reason, a RETURN AUTHORIZATION (RA) number must be issued by B&K in respect of the equipment being returned. You may request an RA number by calling B&K at the numbers below. We ask that you provide the following information at that time. [. . . ]