User manual B&W CWM 800

[. . . ] Placement near a wall/ceiling, wall/floor junction or in a corner is to be avoided as it may give rise to too much bass and a boomy quality to the sound. If possible, keep the speakers more than 0. 5m (20in) from the wall edges. The speakers may be mounted in either portrait or landscape orientation. Wherever possible, however, portrait orientation, with the drive units mounted one above the other, is to be preferred as it gives better horizontal dispersion and a more stable stereo image. [. . . ] Check that there is no debris that may fall into the speaker (especially in ceiling mount situations). IMPORTANT: YOU SHOULD CHECK THAT THE MATERIALS YOU USE MEET THE LOCAL FIRE AND BUILDING REGULATIONS. UNPACKING (figure 1) · Fold the top carton flaps right back and invert the carton and contents. · Lift the carton clear of the contents. · Remove the inner packing from the product. Check the contents: · 2x Baffle with drive units, crossover and foam · 2x Wall frame with swing out dogs · 2x Loudspeaker grille · 1x Alignment template · 1x Accessory pack containing: 8x Self-Tapping screws (for frame to PMK fixing) Not for CWMTM500 8x Machine screws (fixing baffles to wall frames) We suggest you retain the packaging for future use. Remove the grilles and baffles (Not for CWMTM500) from the wall frames and, to avoid damage, keep them in their plastic bags (and preferably in the carton) away from the work area until you are ready to fit them. FITTING THE WALL FRAME New Construction (figure 3) Fit the separately available pre-mount kit ­ (PMK500 for CWMTM500, PMK650 for CWMTM650, PMK800 for CWMTM800) to the studding before the drywall panels are fitted, following the instructions supplied with the kit. The drywall panels should be fitted up to the pre-mount frame and plastered over. Screw, but do not tighten, 4 of the screws provided through the slots in the wall frame into the pilot holes in the pre-mount frame. (The CWMTM500 does not attach to the premount frame directly, but uses the clamping dogs described below). Existing Construction (figure 4) Push out the slots in the template provided. Position the template on the wall as required. Mark along the inside edges of the slots and cut out the aperture neatly. Position the frame in the wall and screw in the 6 (or 4 for CWMTM500, where the baffle/frame is fitted as one assembly) screws visible from the front of the frame. These screws swing out clamping dogs that locate behind the drywall. Ensure that they have located properly and loosely tighten the screws. POSITIONING ­ NEW CONSTRUCTION VERSUS RETROFIT Check that there is no conflict with other in-wall installations (pipe work, air conditioning, powercabling etc. ). In existing construction, use a stud-finding tool to map the wall construction accurately and a pipe detector to scan the proposed installation position. Avoid installing the speakers in the same cavity of the wall as flimsy ducting, which may be induced to rattle. 1 Existing construction Method 2 Using the pre-mount frame in retrofit situations requires that the aperture is cut fairly accurately. Use the template provided to mark out the correct size aperture, having regard to how the wall frame is to be lined up with any features such as door frames, and cut out the aperture neatly. Feed the pre-mount frame through the aperture and pull it forward so that it sits flat on the rear of the drywall and the inner part of the frame protrudes through the aperture. Screw, but do not tighten, 4 of the screws provided through the slots in the wall frame into the pilot holes in the pre-mount frame. All Methods Align the frame squarely and tighten down the screws. A certain amount of flexing of the wall frame is allowed to take up unevenness in the wall surface, but do not over tighten the screws as excessive distortion of the frame may impede the fitting of the baffle. [. . . ] · Soulevez le carton pour le vider de son contenu. · Enlevez les éléments qui protègent l'appareil. Vérifiez le contenu : · 2 x baffle comportant les haut-parleurs, le filtre et de la mousse · 2 x cadre de fixation murale avec oreilles rétractables de maintien · 2 x grille de protection des haut-parleurs · 1 x gabarit d'alignement · 1 x sachet d'accessoires contenant : 8 x vis auto perforantes (pour fixation du PMK à l'ossature) sauf pour le CWMTM500 8 x vis mécaniques pour la fixation du baffle sur le cadre mural I 4979 CWMTM500 CWMTM650 CWMTM800 Drive units 1x 125mm (5in) Kevlar® mid/bass1x 25mm (1in) high-frequency 55Hz ­ 20kHz ±3dB 88dB spl (2. 83V, 1m) 8 3. 5kHz 20W­100W continuous into 8 on unclipped programme. Auto-Reset Polyswitch Height: Width: Height: Width: Height: Width: 228mm (9 in) 175mm (6 7 in) /8 212mm (8 3/8 in) 156mm (6 1 in) /8 217mm (8 1 in) /2 161mm (6 3/8 in) /2 1x 165mm (6 1 in) Kevlar® mid/bass1x 25mm (1in) metal dome high-frequency 50Hz ­ 20kHz ±3dB 89dB spl (2. 83V, 1m) 8 3. 5kHz 20W­130W continuous into 8 on unclipped programme. [. . . ]