User manual BABYSTYLE OYSTER

[. . . ] Instruction manual IMPORTANT ­ KEEP FOR FUTURE REFERENCE Read the instructions carefully before use and keep them for future reference. Your child's safety may be affected if you do not follow these instructions. CONTENTS Page Important Safety Information Primary features Fitting and removing the front wheels Fitting and removing the rear wheels Operating the swivel front wheels Adjusting the handle height Using the parking brake Opening the chassis Fitting the seat unit Removing the seat unit Folding the chassis Folding the chassis with the seat unit fitted Adjusting the seat unit backrest Fitting the carrycot to the chassis Removing the carrycot from the chassis Lowering the carrycot hood Fitting and removing the bumper bar Fitting the Oyster car seat to the chassis Removing the Oyster car seat from the chassis Car seat adaptors Car seat options Fitting removing alternative car seats to the Oyster chassis Using the safety harness Hood/Sun canopy/Insect/UV Net Removing/Fitting the hood Flip out canopy Zippered canopy extension Insect net Fitting the seat unit apron Fitting the footmuff Fitting the stroller rain cover Fitting the carrycot rain cover Care and Maintenance Warranty 3 4 4 5 5 5 5 6 6 6 6 7 7 8 8 8 8 9 9 9 10 10/11 11/12 12 12 12 12 13 13 13 14 14 14/15 15 · Do not place items on the hood/canopy, it may damage the vehicle and/or render it unsafe. · Rubber tyres can leave marks on some surfaces. The tyres can react with some surfaces (vinyl floor coverings, carpets etc. ) and cause stains. [. . . ] Release the quick release button and check that the wheel is locked on. To remove the wheel; push in the front wheel quick release button on the front wheel housing and pull the wheel unit from the axle stub. NOTE, the axle stubs can become greasy and may leave marks on other surfaces they come into contact with. To prevent marking clean the axle stubs with a cloth. To keep the front wheels swivelling freely ensure they are regularly lubricated, if steering becomes stiff, remove front wheel units, clean, lubricate and refit. FITTING THE FOOTMUFF The footmuff top cover can be removed by unfastening the zip. The back part of the footmuff can be used as a seat liner without the top part. To attach the footmuff to the seat unit: Release the harness clips from the centre buckle and release the shoulder straps from the waist belts at the buckle connection. Pass the shoulder straps and waist belts through the corresponding openings in the footmuff. Pass the crotch strap through the opening in the footmuff. Attach the two press-studs at the rear top of the seat backrest to the two press-studs on the top of the footmuff. 4 13 shoulder straps should be clipped into the centre buckle at the end of the crotch strap. The harness can be adjusted to suit your child by sliding the adjusters along the shoulder straps and waist belts. To release the safety harness, push the buttons on the centre buckle. Drings for attaching a separate harness can be found attached to the integral harness at the base of the waist straps. The crotch strap can be adjusted to suit your child. There are two button holes in the seat base. Thread the buckle through the hole in the plastic seat base and then through the opening in seat covers and reposition, passing back through first the seat cover and then through the opening in plastic seat base. The shoulder straps can be adjusted to two positions', thread the buckle through the hole in the plastic seat back and through the opening in the seat cover and reposition passing first through the seat cover and then through the opening in the plastic seat back. Ensure that both shoulder straps are at the same level and that both are secure. WARNING Always use the crotch strap in combination with the waist belt. ALWAYS USE THE SAFETY HARNESS HOOD/SUN CANOPY/INSECT NET The Oyster has a multi function hood that helps to protect your child from the elements. The hood has four sections and a concealed insect net. The hood can also be removed altogether. TO REMOVE/ FIT THE HOOD Release the two press-studs at the back of the hood where the hood attaches to the backrest. [. . . ] While holding the lever, reposition the backrest to the required position. The seat backrest has three positions; upright, intermediate and reclined. When the seat backrest is in the required position, release the lever and the seat will lock into position. 10 7 FITTING AND REMOVING THE BUMPER BAR Push the ends of the bumper bar into the corresponding slots on the seat unit until the bumper bar locks into position. To remove the bumper bar, press in the bumper bar release button on the side of the seat; one on the right side one on the left side. [. . . ]