User manual BALAY 3VN641BD

[. . . ] Instructions for use en 9000 041 066 (8211) en Index 4 5 6 7 8 9 10 Detergents . 12 14 15 16 18 20 21 21 Safety instructions . Getting to know your appliance Water softener . Filling the special salt container Filling the rinse-aid container Unsuitable dishes . [. . . ] This type of product does not generally produce the desired effect with automatic programmes. Products which eliminate the need for regeneration salt can only be used within a certain water hardness range. If you wish to use these combined products, please read the instructions carefully and heed any notes on the packaging. Contact the manufacturer of the cleaning agent if you have any questions, particularly if: the crockery is very wet once the programme has finished. Any problems which arise as a direct result of the use of these products are not covered by our warranty. If you are using detergent in tablet form, read the manufacturer's recommendations on the packaging in order to determine where the tablets should be placed inside the dishwasher (e. g. in cutlery basket, detergent compartment, etc. ). Make sure that the lid on the detergent compartment is closed, even if you are using tablets. 13 en Programme overview This overview lists the max. The programmes supplied with your appliance are indicated on the fascia. Type of crockery e. g. china, Nonpots/pans, delicate cutlery, glasses, etc. Type of food remains Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food a lot stuck on hard Mixed Soups, potatoes, pasta, rice, eggs, roast or fried food Coffee, cakes, milk, sausage, cold drinks, salads very little Amount of food remains Condition of food remains Wash programme a little Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. loosely attached Intesive 70° Normal 65° Eco 50° Quick 35° Pre-rinse Programme sequence Pre-rinse 50° Wash 70° First rinse Second rinse Third rinse Rinse-aid 70° Drying Pre-rinse Wash 65° First rinse Second rinse Rinse-aid 70° Drying Pre-rinse Wash 50° Main rinse Rinse-aid 65° Drying Wash 35° Main rinse Rinse-aid 55° Pre-rinse 14 en Washing dishes Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc. , as well as the amount and condition of food remains, with the details contained in the programme overview. The corresponding programme sequence, duration and consumption details are shown in the bottom half of the overview. For example: Use the "Normal" programme for dishes and utensils which have plenty of food remains stuck on hard. If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Switching the dishwasher ON Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 6 is pressed. The programme starts automatically. End of programme The programme has come to an end when the PROGRAMME END indicator 3 and the indicator for the selected programme are both lit up. Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. Interrupting the programme Set main switch 1 to OFF. The programme is retained in the dishwasher memory. If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may fly open due to expansion. In order to continue with the stored programme, set the main switch to ON again. Programme data The stated programme data are based on standard operating conditions. [. . . ] If the appliance is not connected via a plug, the installation side must feature an all-pole disconnector with a contact gap of at least 3 mm in order to satisfy the relevant safety regulations. Waste water connection See the installation instructions for the required connection steps. If required, attach a siphon with drainage spigot. Using the enclosed parts, connect the waste water hose to the drainage spigot of the siphon. Ensure that the drainage hose is not kinked, crushed or twisted (ensure that there is no sealing cover which prevents the waster water from flowing away!). 21 en Fresh water connection Using the enclosed parts, connect the fresh water connection to the tap according to the installation instructions. [. . . ]