User manual BARKER & WILLIAMSON AXS-160 TRAP ANTENNA

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BARKER & WILLIAMSON AXS-160 TRAP ANTENNA. We hope that this BARKER & WILLIAMSON AXS-160 TRAP ANTENNA user guide will be useful to you.

Lastmanuals help download the user guide BARKER & WILLIAMSON AXS-160 TRAP ANTENNA.


Mode d'emploi BARKER & WILLIAMSON AXS-160 TRAP ANTENNA
Download
Manual abstract: user guide BARKER & WILLIAMSON AXS-160 TRAP ANTENNA

Detailed instructions for use are in the User's Guide.

[. . . ] BARKER & WILLIAMSON 603 CIDCO ROAD COCOA, FL 32926 321-639-1510 MODEL AXS-160 ANTENNA 160 and 30 Meter Bands Power Rating: 2000W PEP, 1000W Output Length: 95 Feet The Barker & Willamson Model AXS-160 is an extra short dipole for the 160 and 30 meter amateur bands. This antenna has a loading coil which makes the antenna extra short in comparison to a standard dipole (approx 250 feet long at 1. 850 Mhz). All short dipole antennas will have a bandwidth narrower than a full size half wave dipole. [. . . ] (2) Remember that throughout the assembly procedure, wire lengths are always to be symmetrical on both sides of the antenna. Your traps may or may not have a color dot on one end of them. The wires must be cut approximately 2 - 3 feet longer than the dimensions shown in figure 1. This is to leave room for the hookups and tuning adjustments. Here are the lengths that you should cut (including the 2 - 3 ft extra). Cut two wires 25', and two wires 28'. Remember, you can always trim the wire shorter after tuning, but once cut too short . (4) Attach one end of the wire segments in the permanent manner shown in figure 2, working out from the center conductor. Allow roughly 6 to 8" of wire through the eyebolt before starting your wrap. Attach the 25' segments to both sides of the center connector. Attach the 28' segments to one side of the LC-1 loading coils. (5) Now assemble the sections of the antenna together paying attention to figures 1 and 3. The wire segment lengths shown are your starting point for tuning the antenna. Make sure that you make temporary connections as shown in figure 3. This will leave each wire segment with one end permanently soldered, and the other end temporarily connected for adjustment. (6) Raise your antenna, and check the VSWR on 30 meters. [. . . ] Warranty is voided if product is subject to misuse, neglect, accident, improperly installed or used in violation of the instructions furnished by us. We reserve the right to make changes in design at any time without obligation to update previously manufactured models. This warranty is given in lieu of any other warranty, expressed or implied. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BARKER & WILLIAMSON AXS-160 TRAP ANTENNA

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BARKER & WILLIAMSON AXS-160 TRAP ANTENNA will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag