User manual BARRACUDA F101 INSTALLATION REV 1.3

[. . . ] 17 Serial Connection via Console Port . 17 4 General Introduction The information in this user guide has been carefully reviewed and is believed to be accurate. It is valid from Barracuda NG Firewall firmware version 5. 0. Barracuda Networks assumes no responsibility for any inaccuracies that may be contained in this document. [. . . ] Put the server board and peripherals back into their antistatic bags when not in use. For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the server board. After accessing the inside of the system, close back the system and secure it to the rack unit with the retention screws after ensuring that all connections have been made. · 7 Safety Instructions Introduction and Package Contents Your new Barracuda NG Firewall F100 / F101 is an integrated security appliance preinstalled with Barracuda NG Firewall firmware. This winning combination offers a ready to run security solution that is flexible, affordable and easy to deploy. Hardware Configuration Table 1 Hardware Component CPU Memory Flash Disk Form Factor Dimensions (W/D/H) Net Weight Power Supply Input Voltage Power Supply Output Voltage Power Supply Frequency Power Supply Watts Storage Temperature Operation Temperature Relative Humidity Certifications WiFi (F101 only) Description VIA 500 MHz 1 GB 4 GB Desktop 5 x 36 x 19 cm 3, 5 kg 100 - 240 V, AC 12 V, DC 47 Hz - 63 Hz 60 W -20 °C - +70 °C 0 °C - 40 °C 5% - 95%, non-condensing CE, FCC, ROHS 802. 11 b+g or better extended range WiFi adapter The hardware configuration list in Table 1 was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological progress. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks NG Firewall or NG Control Center appliance it was delivered with. 8 Appliance Installation Guide Inspecting the Package The following items are included in the package: · · · · · · · · · One security appliance One power cord One power supply One ethernet crossover cable (red) One ethernet standard cable (grey) One serial cable (console) Printed Quick Start Guide One USB flash drive including documentation and administrative tools One antenna to me mounted to the WiFi adapter (F101 only) Please contact Barracuda Networks support if any of these items is missing. 9 Introduction and Package Contents Powering Up and Down This chapter describes the procedure used to install your appliance and perform the initial configuration. Powering Up the Appliance · · · · Connect and power on the appliance. The current status of the boot process will be shown on the appliance's LCD display. You may also use the serial console for this purpose. After a few seconds, the boot process will be initiated and the status LED should start to blink green. Wait until the status LED indicates constant green: The booting procedure is finished. Powering Down the Appliance You must never turn off the appliance by simply switching it off or otherwise removing power from it. Always initiate a proper system shutdown as described below. · · · The system shutdown must be initiated either using the Barracuda NG Admin tool, a remote logon to the appliance or by using the LCD display and keypad on the appliance. The current status of the shutdown process will be shown on the appliance's LCD display. You may also use the serial console for this purpose. The status LED will turn off at the end of the shutdown procedure. 10 Appliance Installation Guide The Status LED Your appliance is equipped with a variety of LEDs. It is either labeled with a heart symbol or the term Status. It indicates the appliance's operational state by changing colors between green, orange and red and by changing between blinking and steady glowing. The table below shows the different meanings of the different glowing states. Table 2 Status LED Conditions Color Off Glowing State Off Meaning Installation Appliance is powered off or installation has not initialized far enough for LED control when installation is started. Installation was completed successfully, appliance is halted for reboot or installation was not yet initialized far enough for LED control. Meaning Normal Operation or ART Appliance is powered off. Appliance is either booting, shutting down or performing a system update. Barracuda NG Firewall is up and running. An error has appeared preventing Barracuda NG Firewall from entering the up state. Green Blinking Green Steady Red Blinking Error during installation. If no orange light available: appliance is in ART mode. For hard disk based appliances, an installation "*. iso" image as well as a backup PAR file are stored within a dedicated partition on the hard drive and will be used. [. . . ] 1 Front panel of the F100 / F101 appliance. Below the appliance's back side with the connectors. The F100 / F101 has four 10/100 MBit ethernet ports on its backside. These ports are labelled with numbers from 1 to 4. The figure above shows the locations of the connectors on the back side with the management port 1 highlighted. [. . . ]