User manual BARTSCHER 10 GN 1-1 SCHEMA

[. . . ] · Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your appliance. · Because these following operating instructions cover various models, the characteristics of your refrigerator may differ slightly from those described in this manual and not all warning signs may be applicable. If you have any questions or concerns, contact your nearest service center or find help and information online at www. samsung. com. [. . . ] Water line installation kits are available at extra cost from your dealer. We recommend using a water supply kit that contains copper tubing. 2. Loosen the controller screw 3 with a Phillips screwdriver. Check the accessory list below. 3 Water filter Hex wrench Fastener 3. Find the best level to align the door slope. Compression fitting Compression nut Connecting to the water supply line 1. First, shut off the main water supply line and turn the ice-maker off. Locate the nearest cold water drinking line. After connecting the water supply with water filter, turn on water supply and Flush 3L through filter before use (flush approximately 6 minutes). Example) The slope is about 2mm (0. 08inch) as shown below. Slope 1 Cold water line Reference plane 2 Pipe clamp 3 Water line - Rotate the Height Adjuster to -2. 0 to reduce the door slope. installation kit After adjustment, first tighten screw 3 and then screw 2 . 4 Shut off valve cHEcKING THE WATER lINE A water dispenser is one of the helpful features on your new Samsung Refrigerator. To help promote better health, the Samsung water filter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You may need to purchase a water purifying system to do INSTAllING THE WATER lINE Connecting the water line to the Refrigerator. There are several items that you need to purchase to complete this connection. You may find these items sold as a kit at your local hardware store. 10_ Setting up · 6. 35mm compression nut · plastic tubing · copper tubing · ferrule Refrigerator 1 Compression nut (6. 35mm) (Supplied) Plastic tubing (Supplied) Compression fitting (Supplied) 2 3 01 SETTING up 02 OpERATING Ferrule (Not supplied) Bulb Compression nut (6. 35mm) (Not supplied) Sticker (month indicator) copper tubing or plastic tubing (Not supplied) (Not supplied) Household water line 1. Run water through the dispenser until the water runs clear (approx. This will clean the water supply system and remove air from the lines. Additional flushing may be required in some households. Open the Refrigerator door and make sure there are no water leaks coming from the water filter. Be sure to flush the dispenser thoroughly or water may leak from it. This is due to the fact that there is still air in the line. Setting up _11 Operating the BARTSCHER refrigerator uSING THE cONTROl pANEl 1 2 3 4 5 6 3 Alarm/ Hold 3 sec for Filter Reset Button 4 The filter Indicator will be Blue when you initially insert the water filter. The filter Indicator will be Light Pink when you have used your water filter for 5 months. The filter Indicator( ) will be Red when you have used your water filter for 6 months. Press the Lighting button( ) to turn on the dispenser LED lamp. Press the Fridge/Hold 3 sec for Power Cool button( ) to set the fridge to your desired temperature. You can set the temperature between 1ºC and 7ºC. [. . . ] · Some heat is normal as anti-condensators are installed in the vertical hinged section of the Refrigerator to prevent condensation. Condensation can occur when you leave the door open for a long time. · Did you wait for 12 hours after installation of the water supply line before making ice?· Is the water line connected and the shut-off valve opened? [. . . ]