User manual BARTSCHER 205460

[. . . ]  The appliance must be installed by a qualified professional according to the instructions provided.  Any necessary adjustment or maintenance must be performed after the cooker has been disconnected from the electricity supply. Room ventilation The appliance may only be installed in permanentlyventilated rooms, according to current national legislation. The room in which the appliance is installed must be ventilated adequately so as to provide as much air as is needed by the normal gas combustion process (the flow of air must not be lower than 2 m3/h per kW of installed power). [. . . ] directive 2002/40/EC on the label of electric ovens. Standard EN 50304 Declared energy consumption for Natural convection Class – heating mode: =Static EC Directives: 73/23/EEC dated 19/02/73 (Low Voltage) and subsequent amendments 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent amendments 90/369/EEC dated 29/06/90 (Gas) and subsequent amendments 93/68/EEC dated 22/07/93 and subsequent amendments 2002/96/EC. Burners ENERGY LABEL 5 Description of the appliance GB Overall view ELECTRIC HOTPLATE Gas burner Hob grid Control panel Containment surface for spills GUIDE RAILS for the sliding racks position 5 position 4 position 3 position 2 position 1 Adjustable foot GRILL DRIPPING PAN Adjustable foot Control panel SELECTOR Knob THERMOSTAT knob THERMOSTAT indicator light ACTIVE HOTPLATE indicator light ELECTRIC HOTPLATE control knob TIMER knob* GAS BURNER ignition button* Hob BURNER control knobs * 6 Only available in certain models. Start-up and use Using the hob Lighting the burners For each BURNER knob there is a complete ring showing the strength of the flame for the relevant burner. To light one of the burners on the hob: 1. Bring a flame or gas lighter close to the burner. Press the BURNER knob and turn it in an anticlockwise direction so that it is pointing to the maximum flame setting -. Adjust the intensity of the flame to the desired level by turning the BURNER knob in an anticlockwise direction. This may be the minimum setting +, the maximum setting - or any position in between the two. If the appliance is fitted with an electronic lighting device* (see figure), press the ignition button, marked with the symbol , then hold the BURNER knob down and turn it in an anticlockwise direction, towards the maximum flame setting, until the burner is lit. The burner may be extinguished when the knob is released. Practical advice on using the electric hotplates To avoid heat loss and damage to the hotplates use pans with a flat base, whose diameter is no less than that of the hotplate itself. setting 0 1 2 3 4 5 6 Normal or Fast Plate Off Cooking vegetables , fish Cooking potatoes (using steam) soups , chickpeas , beans. Continuing the cooking of large quantities of food, minestrone For roasting (average) For roasting (above average) For browning and reaching a boil in a short time. The extremely high and direct temperature of the grill makes it possible to brown the surface of meats and roasts while locking in the juices to keep them tender. 8  Before using the hotplates for the first time, you should heat them at maximum temperature for approximately 4 minutes, without placing any pans on them. During this initial stage, their protective coating hardens and reaches its maximum resistance. For a crispy crust, do not use the dripping pan as it prevents the crust from forming by extending the total cooking time. • If the pizza has a lot of toppings, we recommend adding the mozzarella cheese on top of the pizza halfway through the cooking process. GB Practical cooking advice  In the GRILL cooking mode, place the dripping pan in position 1 to collect cooking residues (fat and/or grease). gRILL • Insert the rack in position 3 or 4. Place the food in the centre of the rack. [. . . ] Any remaining drops of water should also be dried.  Do not close the cover when the burners are alight or when they are still hot. Inspecting the oven seals Check the door seals around the oven regularly. If the seals are damaged, please contact your nearest Authorised After-sales Service Centre. [. . . ]