User manual BARTSCHER A150.0507 PARTS LIST

[. . . ] 22 Utensil Insert for the Cutlery Basket . 34 3 Contents Cleaning and care . Cleaning the filters in the wash cabinet. Cleaning the drain pump and non-return valve. [. . . ] For rinsing dishes if a complete program is not yet needed. 50 % 3) 50 % 3) The dispensing method will depend on the type of detergent being used: 1) Use this ratio for: ­ detergents which contain phosphates and chlorine Divide the total amount, as shown, between compartment I and compartment II. 2) Use this ratio for: ­ detergent which is chlorine and phosphate free ­ detergent which is chlorine free but contains phosphates In this instance the whole amount is placed in compartment II. 3) Use half of your normal amount of detergent. For the NORMAL and INTENSIVE programs, one to two tablespoons of detergent is usually sufficient for excellent wash results. 30 Program chart Program cycle 1. Preliminary Pre-wash pre-wash Usage Electric (kWh) Hot water connection (49 °C / 120 °F) Water Liters/ Gallons 4) Duration Minutes (approx. ) Main wash Interim Final rinse rinse Drying X X X X X 0. 9 19. 6 / 5. 2 104 X X X X X 1. 2 19. 6 / 5. 2 109 X X X X X X 0. 9 24. 5 / 6. 5 109 X X X X X X 1. 0 24. 5 / 6. 5 110 X X X X X 0. 8 5) 0. 06 14. 7 / 3. 9 5 / 1. 3 83 5) 8 4) For models without water softener 5) With half loads (6 place settings) X = cycle being used 31 Operating the dishwasher Operating the dishwasher Turning on. Close the door. Open the water valve (if closed). If you turn the Program knob past your desired program by mistake: Turn the Temperature selector to "OFF". Turn the program knob clockwise past the 12 o'clock position, until the desired program is reached. The new program will start. Changing programs. Wash temperatures can be changed while a program is running, by turning the Temperature selector. If a different wash program is desired, follow the above procedure. Turn the Program knob clockwise to the desired program. Turning off. When finished, the program will stop automatically. Your Miele dishwasher is designed to shut off the water flow and drain the machine in the rare event of a valve failure. They can be easily cleaned as follows: Dishwashers with cutlery basket: Unscrew the upper spray arm. Dishwashers with cutlery tray: Pull out the cutlery tray. Push up on the upper spray arm to engage the tooth-wheel mechanism and then unscrew the spray arm. To remove the middle spray arm located beneath the upper basket, gently push upwards until it engages in the ratchet b, then unscrew it c. To clean the spray arms, use a pointed object to push the the food particles into the jets. Rinse under running water to complete the process. Important: After replacing the spray arms, check that they rotate freely. Lift up on the lower spray arm to remove it. 37 Cleaning and care Cleaning the drain pump and non-return valve. Use caution when cleaning the filters, non-return valve or drain pump, as glass or bone splinters may be caught in the bottom of the wash cabinet. If the water in the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. To clean them: Remove the combination filter. Use a jug or bowl to scoop the water out of the wash cabinet. Rinse the non-return valve under running water. Tilt the locking clamp to the side. The drain pump is situated under the non-return valve (see arrow). [. . . ] Install the 3/8" compression to 3/4" MHT (Male Hose Thread) adapter (supplied with the machine), as illustrated. Connect the inlet hose to the existing valve/adapter assembly. Electrical wiring and components should not come into contact with any plumbing fixtures or hoses. Do not, under any circumstances, cut the intake hose. If the hose is cut, the dishwasher will not work, you will have a water leak and you could be injured. [. . . ]