User manual BARTSCHER TF 404 E 111445 CONTROL PLAN

[. . . ] Make sure the levers are pulled forward. 7 Lower the right end into the fuser unit. 1 Remove the oil roller packaging. 2 Turn it over and look at the gear end: if you see a blue shipping retainer, remove it. 5 Make sure the blue lock lever is toward the back of the printer. 8 Pull the blue lock lever forward to lock the oil roller in place. 3 Open the printer cover. 6 Lower the oil roller into the fuser unit, sliding the left end under the retaining ledge. Setup Guide | 3 4 Prepare the Image Drums Leave !Important:paper ineach drum's protective place. Do not touch the drum's shiny green 1 Remove all image drums and place them next to the printer. 2 Carefully remove the shipping tape and sponge insert from each drum. You may want to do this holding the drum over a trash can to catch any toner clinging to the sponge. 4 Place the image drums back into the printer, matching the color coded label with the label in the printer. © © 3 Remove the shipping tape and spacers from inside the printer. © © © © 4 | BARTSCHERCOLOR 8 © © © © To catch any toner spillage, you may want to set the drums on a few sheets of paper. light can ! [. . . ] 2 Double-click the CD icon that appears on the desktop. 6 Double-click the BARTSCHERCOLOR 8 Installer. 7 Continue with the installation following the instructions on your screen. Select the Printer: 1 2 Print the BARTSCHERCOLOR 8 menu: press ON LINE on the printer's control panel, then press and hold PAPER SIZE/Print Menu for two seconds until PRINT MENU displays. 2 On the printout, under ETHERTALK, Printer Name, note the name that appears, for example, BARTSCHER_465987. 5 Highlight the name from step 2, and click SETUP. The PostScript Printer Description (PPD) setup screen appears. 6 Click Auto Setup to have the Adobe Printer Driver configure your printer automatically OR Click Select PPD to select a PPD file manually. 7 Follow the instructions on your screen to finish. The Demo page prints. Setup Guide | 7 11 Calibrate the Color This is an important process to make sure your BARTSCHERCOLOR 8 gives you sharp, accurate color images. There are two parts: 1 Color Registration, and 2 Color Balance. Setting the Color Registration Since each color is printed separately, you must set the color registration to ensure that the colors line up properly. If the colors are out of alignment, the printed page will appear blurry and unclear. To ensure optimum print quality, you should set the color registration on a routine basis (once a month or so). This sends the new settings to the printer and prints a color balance verification page. The utility2 to check the color resets the to its default settings each time it prints the test pattern. Macintosh 1 Start the utility: · Windows systems: click Start ® Programs ® BARTSCHERCOLOR 8 ® BARTSCHERCOLOR 8 Color Balance Utility. · Macinstosh systems: in the BARTSCHERCOLOR 8 Macintosh Folder, double-click theColor Balance Utility. 2 Make sure BARTSCHERCOLOR 8 is selected. Click Reset and Print Adjustment Page to print a color balance adjustment page. Congratulations!Your BARTSCHERCOLOR 8 is ready to print beautiful color documents. 7 Repeat steps 5 and 6 for the remaining eight sections. This time, the box in each section where no color shows should be in the +1, 0, or -1 range for all 9 sections. If they aren't, repeat steps 4 through 6 until they are. 9 Click Close. Setup Guide | 9 Control Panel Status Low Toner Indicators *Printer Language Buttons Paper Size Paper Source Buttons The control panel buttons are dual function: press and release to engage the top function; press and hold for 2 to 3 seconds to engage the bottom function. Press: Enters and scrolls through Level 1 menu. Press: In Menu Mode returns to previous item. [. . . ] Oki Data also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by Oki Data. Written and produced by the Oki Data Training & Publications Department. Please address any comments on this publication · by mail to: Training & Publications Department Oki Data Americas, Inc. [. . . ]