User manual BAUKNECHT WMH2175XVS INSTALLATION

[. . . ] MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS This product is suitable for use above electric or gas cooking products up to and including 36" (91. 4 cm) wide. See "Installation Requirements" section for further notes. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions. Table of Contents MICROWAVE HOOD COMBINATION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Using a keyhole saw, cut out the venting cutout area. 3. Holding the cardboard template in place, mark both holes in the lower corners, and draw a horizontal line across the bottom edge of the cardboard template. These represent the mounting plate's end holes and bottom edge. Remove the cardboard template and check the markings: Centerline Upper cabinet bottom Drill Holes in Rear Wall In addition to being installed on at least 1 wall stud, the mounting plate must attach to the wall at both end holes. If the end holes are not over wall studs, use two 1/4-20 x 3" round-head bolts with toggle nuts; if 1 end hole is over a wall stud, use 1 lag screw and one 1/4-20 x 3" round-head bolt with toggle nut; or if both end holes are over wall studs, use 2 lag screws. Following are 3 installation configurations. 15³/" (40. 0 cm) 17¹/" (43. 8 cm) 14¹/" (35. 9 cm) 14¹/" (35. 9 cm) Installation for No Wall Studs at End Holes (Figures 1 & 2) 1. Drill 3/4" (19 mm) holes through the wall at both end holes marked in Step 3 of "Mark Rear Wall. " 2. Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole(s) marked in Step 6 of "Mark Rear Wall. " Refer to figures 1 and 2 in "Possible Wall Stud Configurations" in "Locate Wall Stud(s)" section. Mounting plate end hole Bottom of mounting plate The bottom edge line must be 17¹/" (43. 8 cm) from the bottom of the upper cabinet, and must be level. The end holes must be 15³/" (40. 0 cm) from the bottom edge of the upper cabinet, and must be on a level line with each other. They must each be 14¹/" (35. 9 cm) from the centerline. 7 Installation for Wall Stud at One End Hole (Figure 3) 1. Drill a 3/16" (5 mm) hole into the wall stud at the end hole marked in Step 3 of "Mark Rear Wall. " 2. If installing on a second wall stud, drill a 3/16" (5 mm) hole into the wall stud at the other hole marked in Step 6 of "Mark Rear Wall. " Refer to Figure 3 in "Possible Wall Stud Configurations" in "Locate Wall Stud(s)" section. Drill a 3/4" (19 mm) hole through the wall at the other end hole. 5. Insert lag screw(s) into the hole(s) drilled into wall stud(s) in Step 2 of "Installation for No Wall Studs at End Holes" in the "Drill Holes in Rear Wall" section. Check alignment of mounting plate, making sure it is level. Securely tighten all lag screws and bolts. Wall Stud at One End Hole (Figure 3) 1. With the support tabs of the mounting plate facing forward, insert a 1/4-20 x 3" round-head bolt through the end hole that fits over the 3/4" (19 mm) hole drilled in Step 3 of "Installation for Wall Stud at One End Hole" in the "Drill Holes in Rear Wall" section. Start a toggle nut on the bolt from the back of the mounting plate. Leave enough space for the toggle nut to go through the wall and to open. Push the bolt with toggle nut through the drywall, and finger tighten the bolt to make sure toggle nut has opened against drywall. Insert a lag screw into the remaining end hole. If installing on a second wall stud, insert a lag screw into the other hole drilled in Step 2 of "Installation for Wall Stud at One End Hole" in the "Drill Holes in Rear Wall" section. [. . . ] 90° elbow: 3¹ " x 10" = 25 ft (8. 3 x 25. 4 cm = 7. 6 m) D. 90° elbow: 6" = 10 ft (15. 2 cm = 3 m) E. Wall cap: 3¹/" x 10" = 40 ft (8. 3 x 25. 4 cm = 12. 2 m) F. 45° elbow: 6" = 5 ft (15. 2 cm = 1. 5 m) G. [. . . ]