User manual BECKER 4720 TRAFFIC PRO UPDATECD3 8

[. . . ] Navigation CD 8. X If you received this operation guide update when purchasing a new unit, the functions and modifications described from page 21 are intended as a supplement to your operation guide. If you received this operation guide update together with an update CD, the update procedure and the new functions and modifications are described on the following pages. As basis for this description, it is assumed that you already own the CD 3. X, CD 4. X, CD 5. X, CD 6. X or CD 7. X. you have previously used a Navigation CD 2. X, then the required information can be found in the description for the CD 3. 0, which is also enclosed. Installation of CD 8. X In order to install CD 8. X, remove the old CD and insert the new CD 8. X. [. . . ] Then, press the right rotary control to confirm the category. Note: If the set user language is identical with one of the languages available on the CD, the categories are displayed in this language. If there is no correspondence, the categories are displayed in all available languages. This can be recognised by the country abbreviations in front of the category. If the points of interest CD is inserted during active navigation, the system requests information on the location of the point of interest (near to destination or in vicinity of current position). If navigation is not active, this selection is skipped. Press the right rotary control . The valid categories for the current points of interest CD are displayed. With the right rotary control, select either !!.  !# or C ; R!I! OHM q The categories and points of interest shown in the illustrations are examples. The actual display is dependent upon the CD used. Subject to errors and technical modifications After a short time, the available points of interest for the selected categories are displayed. 27 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 8. X The arrows following the distance information indicate the direction of the relevant point of interest (e. g. point of interest lies in the direction of travel, point of interest lies in the opposite direction to that of travel). Then, turn the right rotary control to select the desired point of interest. The point of interest is accepted by pressing the rotary control . · to select the desired setting. Use the right rotary control · !& # ! The display shows the remaining travel time. ! The display shows the estimated time of arrival. · ! With this setting the unit adjusts ETA for faster drivers. · The display shows the current time. Selection is confirmed by pressing the control. The system returns to the system settings menu. This is the default setting. It offers a sufficiently accurate calculation of ETA for most drivers. · $p With this setting the unit adjusts for drivers who may take longer for the planned journey. This setting could be used, for example, in areas of dense traffic. Selection is confirmed by pressing the control. The system returns to the system settings menu. Subject to errors and technical modifications 29 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 8. X Switching the speed limits display on/off If the speed limits display is ON, the system will inform you of the maximum permissible speed limit for the route along which you are travelling during route guidance, insofar as this information is available. If, when the speed limit display is ON, you travel along a route with a speed limit and this speed limit is stored on the navigation CD, the corresponding symbol will appear on the right-hand side of the display indicating the speed limit. TV Y P GWarning hazard Accident Road traffic regulations always take priority when a vehicle is being driven in traffic. [. . . ] An inverse TP appears on the display to indicate that the traffic programme is active. Subject to errors and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 8. X Activating/quitting the TP menu Activating: Press the not be transmitted). , + !7 ;( #63 !4* 73 button (traffic announcements can- , ## !7 ;( #63 !4* TP is switched off after returning to normal display. Selecting automatic tracking Press the !7 multifunction button. Quitting: Press the 73 button or the TP menu will be automatically terminated after 8 seconds without actuation. Switching TP on/off In all modes and wavebands, TP can be switched on/off by pressing the 73 button for more than 2 seconds. TP can also be switched on/off in the TP - menu. Switching on: To switch on TP in the TP menu, press the !7 multifunction button repeatedly until !65 is displayed. , + !7 ;( #63 !4* Only applies when TMC is switched off. [. . . ]