User manual BECKER 7820 TRAFFIC PRO HS UPDATECD1 3

[. . . ] Navigation mode can only be selected after completion of navigation software installation. Subject to errors and technical modifications 13 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 3. X Modifications to navigation mode The following modifications have been made to navigation mode or the following new functions have been added. · · · · Navigation CDs Destination input via coordinates Switching the speed limits display on/off Dynamic navigation with TMC Navigation CDs Two navigation CDs are supplied with the navigation unit. These CDs contain a digitised street map. 1) and one CD for Southern Europe (CD no. [. . . ] Route guidance can now start. YYYYYYYYYYYYYYYYYYYYYYYYYYY YYY YYYYYY Subject to errors and technical modifications 16 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 3. X Switching the speed limits display on/off If the speed limits display is ON, the system will inform you of the maximum permissible speed limit for the route along which you are travelling during route guidance, insofar as this information is available. If, when the speed limit display is ON, you travel along a route with a speed limit and this speed limit is stored on the navigation CD, the corresponding symbol will appear on the right-hand side of the display indicating the speed limit. TV Y P GWarning hazard Accident Road traffic regulations always take priority when a vehicle is being driven in traffic. Road signs en-route should always be heeded. In some cases, the speed limit indicated by the navigation system may be incorrect. At all times, the driver must decide whether or not to heed the speed limit indicated. We do not accept liability for erroneous data provided by the navigation system. !"! T The distance to the next point at which for example a turn should be made is displayed below the navigation arrow, which appears in reduced format. On routes with variable speed limits (dependent on weather conditions, time of day etc. ) a symbol with the text @5Y or a speed with an underscore (e. g. : "80") draws the driver's attention to the fact that the speed limit is variable. due to road works) are usually short-lived, these have not been included on the CD.  ! !! Set and confirm ! in the System Settings menu. F By pressing the right rotary control selection can be made between speed limits display or . Setting is confirmed and accepted by pressing and holding the right rotary control . Subject to errors and technical modifications 17 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 3. X Dynamic navigation with TMC Note: Dynamic route guidance is not possible in all countries. To use dynamic navigation and the functions described below, TMC must be switched on, as described under "Switching TMC on/off" on page 22. When any route recalculations are made with active dynamic route guidance, the navigation system may request the Navigation CD (if the Navigation CD is not already inserted). Dynamic route guidance is used to calculate the route, taking current traffic announcements into account. The traffic announcements are transmitted by a TMC radio station in addition to the radio programme and are received and analysed by the navigation system. There is no charge for receiving traffic announcements. Note: Traffic announcements are transmitted by radio stations, therefore we cannot accept any responsibility for the completeness and correctness of the announcements Activating dynamic route guidance Dynamic route guidance can be started by selecting !!S&Y Y in the route menu. Austria: The location and event code was made available by ASFINAG and BMVIT. Note: Can only be selected if TMC has been switched on or is currently switched on. See "Switching TMC on/ off" on page 22. # !! D F F " Y If !!S&Y !!S !"! is not displayed immediately (display or !Y ), then & must be selected by entering the route settings. Y Y Subject to errors and technical modifications 18 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 3. X Note: ! [. . . ] If TMC is switched off, a traffic programme transmitter can be selected freely. Note: Dynamic navigation functions (dynamic route, traffic information) cannot be selected or called up. Using the right rotary control , select <;6:, 3, *; and press to confirm. After a short delay and without actuation, the direct programming is deleted. Quit the TP menu. Subject to errors and technical modifications 22 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 3. X Display for TMC stations If a radio station transmits TMC information in addition to the radio programme, this is indicated on the display by the abbreviation !. [. . . ]