User manual BECKER VISION PRO 7877 INSTALLATION GUIDE

[. . . ] We strongly recommend that you have the unit installed by a specialist workshop. Risk of injury Installing the components incorrectly may lead to injuries in the event of a road traffic accident or render safety devices ineffective. Please refer to the instructions provided by the vehicle manufacturer. Damage to the airbag Installing the components in the wrong location may damage the airbag or impair its operation. [. . . ] 34 DVD player Securing tab ! · Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide · Connect the power supply cable (M). Connect the black lead to terminal 31 (ground) Connect the orange lead to terminal 15 (switched voltage) Connect the red lead to terminal 30 (permanent positive) G Risk of fire by removing the fuses The fuses incorporated into the cable harness must be used. Without fuses, there is a risk of fire or damage to the components. In order to avoid malfunctions, it is absolutely essential to observe the relevant cable cross-section when using branch connections/cable connectors. If desired, create the connection to the AUX inputs of the car radio using the car radio AUX (O) connecting cable. Once you have created this connection, the sound of the Rear Seat Entertainment system can be output via the existing vehicle speakers. The Rear Seat Entertainment system can also be operated without AUX connection by using the headphones supplied. Connect the DVD player to the connection box using the corresponding connecting cable (N). Connect the connecting cable (L) to the screen unit (A). ! · ! · · Subject to errors and technical changes 35 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 9. General information on installation of the screen in the vehicle Ideal installation position · The screen should be secured in the centre of the vehicle just behind the front seats to provide the vehicle occupants in the rear with the best possible view of the screen. When deciding on the best installation position, ensure that the screen is not a nuisance to the driver or does not obstruct his view either when open or closed. Check all applicable national regulations and laws. !! · Requirements for attachment in the vehicle Dead weight / vibrations / shocks The weight of the screen unit (A) including the mounting plate (C) is 1, 5 kg. To prevent severe vibrations affecting the screen under normal driving conditions and at the same time to ensure an unimpaired view, the screen must be secured to a frame part of the vehicle. Most vehicles have struts in the roof structure that usually run across the width of the vehicle. The roof structure is attached to these struts, which extend across the entire vehicle. These struts offer the most stable attachment for the screen unit (A). The mounting plate (C) supplied permits the screen to be attached to the struts in the roof structure. · · Subject to errors and technical changes 36 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide · If the struts are too far from the ideal installation location, an extension plate must be used to attach the mounting plate. Attachment points (at least 3 stable attachment points) · The mounting plate or the extension plate must be secured to at least two points of the vehicle's strut structure. This prevents longitudinal movements or lateral rotational movements of the screen when using the screen or folding it down. The third attachment secures the mounting plate when folding down the screen. This attachment can be made directly to the roof panel by installing the plates included in the installation kit as well as the double-sided adhesive tape. The plastic threaded rod included in the installation kit makes it easier to align the plate. · Vehicles with sunroof · · In vehicles equipped with a sunroof, the screen's mounting plate can usually be mounted directly on the struts to which the frame of the sunroof is also attached. [. . . ] Secure the templates using a threaded nut. · 10. 16 Cutting two cut-outs in the vehicle headlining · Using the cutting template (H) cut out the larger cut-outs. Ensure that you remain in the area of the template. · Remove the cutting template. To complete the cut-out, cut through the remaining segments. Remove the cut-out section of the vehicle headlining. Subject to errors and technical changes 48 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 10. 17 Removing the cutting template from the mounting plate and pull the connecting cable through the cut-outs · Release the two M6 hexagon socket screws for the cutting template bracket and remove the bracket through the cut-outs in the vehicle headlining. [. . . ]