User manual BEGLEC IM-5W

[. . . ] Technical Specifications Power Fuse Lamp Dimension Weight AC 120V~60Hz AC 230/240/250V~50/60Hz 20mm Glass T6. 3A Fast Blow 20mm Glass T5A Fast Blow ELC 24V 250W 290mm x 330mm x 380mm 12 kg IM-5S IM-5W Innovation , Quality , Performance User Guide WWW. BEGLEC. COM 7. Fixture Cleaning The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit's optics. Clean with soft cloth using normal glass cleaning fluid. [. . . ] 3 pin XLR connectors are more popular than 5 pin XLR. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5E 2. Technical Specification · VoltageAC 120V~60Hz or 230V/240V/250V~50/60Hz · BulbELC 24V 250W · The unit is DMX512 fixture. It can be also linked together in master/slave connection, as many as required and run by built-in program chase sequences automatically or by sound activation through an internal microphone to create an intelligent effect. · It can be operated by DMX512 control or can be used as an individual unit without a controller. · Consistent DMX channel enable iRock, iShow and iMove to be link together. · Features different preprogrammed chase patterns. · Please use a 3 pin XLR cable/plug when connecting units together. · Accurate focusable optics system and ultra smooth stepping motors. · Dimension : 290 x 330 x 380 mm · Weight : 12 kg IM-5S Independent gobo wheel with 14 gobos plus open and blackout, including 10 metal, 1 replaceable gobo, 2 glass and 1 effect gobos with shaking and shutter effect, Independent color wheel with 11 dichroic colors with rainbow effect. IM-5W Independent color wheel with 11 dichroic colors with rainbow effect and independent shutter & dimmer. 6E 5. 4 DMX512 Configuration 2. 1 Beam Angel Ch 1 IM-5S IM-5W Pan Pan Ch 2 Tilt Tilt Ch 3 Shutter/Sharking Shutter Ch 4 Gobo No function Ch 5 Color Color Ch 6 No function Ch 7 Dimmer Stand by Blackout the unit Strobe 1. Gobo / Color sync. strobe 3. Two-light strobe Sound 1 (LED off ) Blackout the unit Strobe 1. Color sync. strobe 3. Two-light strobe X/Y moving show mode Color selection selection ( Show 1 ~ Show 4 ) Please refer to Show mode in 4. 2 Main Function X/Y moving setting 1. Pan position 2. Tilt position 3. Dimmer First set Master unit, then set Slave units' position Position/ Latch (LED fast blinking) X/Y moving show mode Color/Gobo selection 1. ( Show 1 ~ Show 4 ) Please refer to Show mode 2. Press shortly for color change in 4. 2 Main Function Sound 2 (LED normal blinking) Slow/Sound 3 (LED on) X/Y moving setting 1. Pan position 2. Tilt position First set Master unit, then set Slave units' position Position/ Latch (LED fast blinking) 3. Lamp In case of replacement of the lamp or maintenance, do not open the fixture within 15 minutes until the unit cools down after switching off. IM-5S Function Mode Stand by ¥ Lamp : ELC 24V 250W 1. Always switch off the main supply and never handle the lamp or luminaries when is hot. If this happens, clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation. Never operate the lamp without appropriate shielding. Make sure the lamp is located in the center for the best spot. IM-5W Function Mode Sound 1 (LED off ) Sound 2 (LED normal blinking) Slow/Sound 3 (LED on) 5. 3. 1 iSolution Operation Consistent DMX configuration enable iMove to be linked together with iRock and iShow and controlled at the same time. DMX address can be set remotely by iLead controller ( please refer to the user manual of iLead controller ). No need to calculate the DMX channels of each fixture in the chain. [. . . ] Tilt Inversion Press the MENU button up to when the is showing on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the (tilt inversion) mode. Once the mode has been selected, press the (normal) or ENTER button to setup or automatically return to the main functions without any change after 8 seconds. [. . . ]