User manual BEGLEC LED BLASTER 108 V1.0

[. . . ] USER MANUAL WWW. BRITEQ-LIGHTING. COM V e r 1, 0 1 1. 1 PRODUCT (GENERAL) PRODUCT INTRODUCTION This product is designed for indoor or outdoor use. Suitable applications include wash or effect lighting for architectural, stage or nightclub applications. This product can also be installed for use in signage and advertising using the dynamic functions available with DMX512 control. Direct input of DMX512 signal allows the units to be controlled from any DMX512 controller. [. . . ] (Note that when using ID addresses it is also possible to activate ADAS which allows for even more options with DMX addressing and control see ADAS Addressing section 2. 2-3) 2. 4-3 ADAS WITH ID ADDRESS(STAGE 1 MODE) Connect the DMX512 controller to the units in series Select ADAS ON from the Settings menu ID Address should be set in the Settings menu on each unit in ascending values (i. e. 1, 2, 3. . . ) ADAS addressing is based on the ID address as follows: ADAS DMX Address = { ADAS fader * (ID Address -1)}+ 1 ADAS addressing is activated by moving CH8 + CH10 faders to the 255 value (CH8 = 255 & CH10 = 255) ADAS addressing is deactivated by moving CH8 + CH10 + CH11 to the 255 value (CH8 = 255, CH10 = 255 & CH11 = 255) When ADAS is deactivated, all DMX addresses will return to their original DMX Address. To permanently store ADAS DMX addresses, select ADAS copy from the Settings menu, on the target fixtures to store the new DMX Address. Example: ID Addr. 1 ID Addr. 2 ID Addr. 3 DMX512 CONTROLLER The figure above shows a simple ID address layout using one DMX address. Each of the units has a different ID address which will receive a new temporary DMX address when ADAS is activated (unless ADAS copy is selected). The user is able to activate and deactivate ADAS at will giving the possibility of creating many different fixture grouping possibilities using the ID address, real DMX address and the ADAS temporary DMX address. Note: When using ADAS, all fixtures must have the following settings from the Settings menu set correctly; ID address ID ON/OFF ADAS fader no ADAS ON/OFF 2 INSTALLATION Each unit should have the target ID address set in ascending order Each unit should set ID On Each unit should be set to the same number of faders as your controller(must be 12) Each unit should be set as ADAS On 8 2008. 8. 13 . . . . . . . . . . . . . . . . . . . . . . . . 3 3. 1 DISPLAY PANEL OPERATION BASIC The LED fixture is mounted with a LCD display and 4 control buttons. SET UP DOWN EXIT enter the currently selected menu or confirm the current function value scroll 'UP' through the menu list or increase the value of the current function scroll 'DOWN' through the menu list or decrease the value of the current function exit from the current menu or function 3 DISPLAY PANEL OPERATION 9 2008. 8. 13 3. 2 MENU MENU Static color Dimmer Red Green Blue Color macros Strobe Dimmer Red Green Blue Color macros Strobe 0 0 0 0 0 0 255 255 255 255 255 255 DMX512 Address Address 1 512 Personality STAGE 1 STAGE 2 PIXEL ARC 1 ARC 1+D Run mode DMX CON Auto program Auto Auto Auto Auto Auto Auto Auto Auto 1 2 3 4 5 6 7 8 Settings ID address ID ON/OFF ADAS fader no ADAS ON/OFF ADAS copy R e s e t to Factory settings Dimmer start ID address 001 06 6 ID ON/OFF ADAS fader no 01 244 ADAS ON/OFF ADAS copy ON/OFF Reset confirm Dimmer start 001 / 005 Password Password ON/OFF Password ON/OFF Set Password Set password 3 DISPLAY PANEL OPERATION 10 2008. 8. 13 3. 3 CREATING A STATIC COLOR MENU Static color Dimmer Red Green Blue Color macros Strobe Dimmer Red Green Blue Color macros Strobe 0 0 0 0 0 0 255 255 255 255 255 255 Static colour Combine RED, GREEN and BLUE to create an infinite range of colors (0-255) Enter Color macros allow to choose 18 color macros Set value of dimmer (0-255) Set the value of the strobe (0-20Hz) 3. 4 DMX512 SETTINGS MENU DMX512 Address 1 512 DMX512 address Enter the DMX address mode to set the DMX address Activate control from outside source by activating ON 3. 5 DMX CHANNEL MODE MENU Personality STAGE 1 STAGE 2 PIXEL ARC 1 ARC 1+D Personality Enter Personality mode to choose DMX mode: PIXEL , ARC 1 or ARC 1+D . STAGE 1 , STAGE 2 , 3. 6 RUN MODE MENU Run mode Enter the Run mode mode to set the working mode DMX mode is for using the DMX512 controller to control the fixtures. Both STAGE 1 and STAGE 2 have two DMX modse: DMX MODE 1 and DMX MODE 2 Ch9 is used to switch from one DMX MODE 1 (0-244) to DMX MODE 2 (245-255). ARC 1 CHANNEL 1 VALUE RED 0 5 4 255 No function 0-100% GREEN FUNCTION 2 0 5 4 255 No function 0-100% BLUE 3 0 5 4 255 No function 0-100% ARC 1+D CHANNEL 1 VALUE DIMMER 0 5 4 255 No function 0-100% RED FUNCTION 2 0 5 4 255 No function 0-100% GREEN 3 0 5 4 255 No function 0-100% BLUE 4 0 5 4 255 No function 0-100% 4 USING A DMX512 CONTROLLER 14 2008. 8. 13 STAGE 1(DMX MODE 1) CHANNEL 1 VALUE RED 0 5 4 255 No function 0-100% GREEN FUNCTION 2 0 5 4 255 No function 0-100% BLUE 3 0 5 4 255 No function 0-100% YELLOW 4 0 5 4 255 No function 0-100% CYAN 5 0 5 4 255 No function 0-100% PURPLE 6 0 5 4 255 No function 0-100% WHITE 7 0 5 4 255 No function 0-100% STROBE 8 0 5 4 255 No function Strobe (slow to fast) MODE SELECTION 0 5 35 65 4 34 64 94 124 154 184 214 244 255 No function Color-Cycle Mode 1 Color-Cycle Mode 2 Color-Cycle Mode 3 Color-Cycle Mode 4 (speed can be adjusted using Channel 11) Color-Cycle Mode 5 Color-Cycle Mode 6 Color-Cycle Mode 7 Color-Cycle Mode 8 DMX MODE 2 9 95 125 155 185 215 245 4 USING A DMX512 CONTROLLER 15 2008. 8. 13 CHANNEL VALUE 0 10 20 9 19 29 FUNCTION ID ADDRESS SELECTION (also see pg. 26) Select all ID addresses ID address #1 ID address #2 ID address #3 30 . 255 209 ID address #20 ID address #21 ID address #22 ID address #23 ID address #66 MODULE SELECTION 0 5 35 65 4 34 64 94 124 154 184 214 255 255 #1 ON #2 ON #3 ON #1 ON #2 ON #3 ON #1 ON #2 ON #2 ON #3 ON #1 ON #3 ON #1 ON #2 ON #3 ON #1 OFF #2 OFF #3 OFF Speed control of CH9 Color-Cycle Mode 4 EFFECT MACRO 11 95 125 155 185 215 0 0 5 4 9 . 14 No function Effect MACRO #1 Effect MACRO #2 . Effect MACRO #50 12 10 250 255 4 USING A DMX512 CONTROLLER 16 2008. 8. 13 STAGE 1(DMX MODE 2) CHANNEL VALUE MODULE #1 0 5 35 4 34 64 94 124 154 184 255 No function RED GREEN BLUE YELLOW PURPLE CYAN PINK-WHITE MODULE #2 0 5 35 4 34 64 94 124 154 184 214 No function RED GREEN BLUE YELLOW PURPLE CYAN PINK-WHITE MODULE #3 0 5 35 4 34 64 94 124 154 184 214 No function RED GREEN BLUE YELLOW PURPLE CYAN PINK-WHITE NO FUNCTION NO FUNCTION NO FUNCTION NO FUNCTION STROBE FUNCTION 1 65 95 125 155 185 2 65 95 125 155 185 3 65 95 125 155 185 4 5 6 7 8 0 5 4 255 No function Strobe (slow to fast) MODE SELECTION 9 0 245 244 255 DMX MODE 1 DMX MODE 2 4 USING A DMX512 CONTROLLER 17 2008. 8. 13 CHANNEL VALUE 0 10 20 9 19 29 FUNCTION ID ADDRESS SELECTION (also see pg. 26) Select all ID addresses ID address #1 ID address #2 ID address #3 30 . 255 209 ID address #20 ID address #21 ID address #22 ID address #23 ID address #66 NO FUNCTION NO FUNCTION 11 12 4 USING A DMX512 CONTROLLER 18 2008. 8. 13 STAGE 2(DMX MODE 1) CHANNEL 1 VALUE DIMMER 0 5 4 255 No function 0-100% RED FUNCTION 2 0 5 4 255 No function 0-100% GREEN 3 0 5 4 255 No function 0-100% BLUE 4 0 5 4 255 No function 0-100% COLOR MACROS 0 10 30 40 50 70 80 90 110 9 29 39 49 69 79 89 109 119 129 149 159 169 189 199 219 229 249 255 No function RED RED+GREEN RED+GREEN YELLOW RED+GREEN RED+GREEN GREEN GREEN+BLUE GREEN+BLUE BLUE BLUE+GREEN BLUE+GREEN CYAN GREEN+PURPLE PURPLE PURPLE+GREEN RGB WHITE STROBE (100%) (R85%+G15%) (R60%+G40%) (100%) (R15%+G85%) (R40%+G60%) (100%) (G85%+B15%) (G60%+B40%) (100%) (G85%+B15%) (G60%+B40%) (100%) (G50%+P50%) (100%) (P80%+G20%) (100%) (100%) 5 120 130 150 160 170 190 200 220 230 250 6 0 5 4 255 No function Strobe (slow to fast) 4 USING A DMX512 CONTROLLER 19 2008. 8. 13 CHANNEL VALUE 0 5 35 65 4 34 64 94 124 154 184 214 244 255 No function FUNCTION MODE SELECTION Color-Cycle Mode 1 Color-Cycle Mode 2 Color-Cycle Mode 3 Color-Cycle Mode 4 (speed can be adjusted using Channel 11) Color-Cycle Mode 5 Color-Cycle Mode 6 Color-Cycle Mode 7 Color-Cycle Mode 8 DMX MODE 2 ID ADDRESS SELECTION (also see pg. 26) 7 95 125 155 185 215 245 0 10 20 9 19 29 Select all ID addresses ID address #1 ID address #2 ID address #3 30 . 255 209 ID address #20 ID address #21 ID address #22 ID address #23 ID address #66 MODULE SELECTION 0 5 35 65 4 34 64 94 124 154 184 214 255 255 #1 ON #2 ON #3 ON #1 ON #2 ON #3 ON #1 ON #2 ON #2 ON #3 ON #1 ON #3 ON #1 ON #2 ON #3 ON #1 OFF #2 OFF #3 OFF Speed control of Ch7 Color-Cycle Mode 4 EFFECT MACRO 9 95 125 155 185 215 0 0 5 4 9 . 14 No function Effect MACRO #1 Effect MACRO #2 . Effect MACRO #50 10 10 250 255 4 USING A DMX512 CONTROLLER 20 2008. 8. 13 STAGE 2(DMX MODE 2) CHANNEL VALUE MODULE #1 0 5 35 4 34 64 94 124 154 184 255 No function RED GREEN BLUE YELLOW PURPLE CYAN PINK-WHITE MODULE #2 0 5 35 4 34 64 94 124 154 184 214 No function RED GREEN BLUE YELLOW PURPLE CYAN PINK-WHITE MODULE #3 0 5 35 4 34 64 94 124 154 184 214 No function RED GREEN BLUE YELLOW PURPLE CYAN PINK-WHITE NO FUNCTION NO FUNCTION STROBE FUNCTION 1 65 95 125 155 185 2 65 95 125 155 185 3 65 95 125 155 185 4 5 6 0 5 4 255 No function Strobe (slow to fast) MODE SELECTION 7 0 245 244 255 DMX MODE 1 DMX MODE 2 4 USING A DMX512 CONTROLLER 21 2008. 8. 13 CHANNEL VALUE 0 10 20 9 19 29 FUNCTION ID ADDRESS SELECTION (also see pg. 26) Select all ID addresses ID address #1 ID address #2 ID address #3 30 . 255 209 ID address #20 ID address #21 ID address #22 ID address #23 ID address #66 NO FUNCTION NO FUNCTION 9 10 PIXEL CHANNEL 1~9 1 2 3 4 5 6 7 8 9 VALUE 0 5 5 5 5 5 5 5 5 5 4 255 255 255 255 255 255 255 255 255 FUNCTION NO FUNCTION BLOCK1-RED BLOCK1-GREE N BLOCK1-BLUE BLOCK2-RED BLOCK2-GREEN BLOCK2-BLUE BLOCK3-RED BLOCK3-GREEN BLOCK3-BLUE 4 USING A DMX512 CONTROLLER 22 2008. 8. 13 4. 3 BASIC INSTRUCTIONS FOR DMX512 OPERATION STAGE 1 DMX MODE 1 RED, GREEN & BLUE COLOR SELECTION CH1, CH2 & CH3 control the intensity ratio of each of the RED, GREEN & BLUE LEDs. When the slider is at the highest position (255) the intensity of the color is the maximum. CH1, CH2 & CH3 can be combined together to create over 16 million colors. [. . . ] 1) to select DMX mode 2 to select ID Add: 1 to select GREEN for MODULE #1 (ID Add. 2) to select OFF for MODULE #3 to select DMX mode 2 to select all ID Addresses to select OFF for MODULE #1 (ID Add. 2) to select GREEN for MODULE #2 (ID Add. 2) to select DMX mode 2 to select all ID Addresses to select OFF for MODULE #1 (ID Add. [. . . ]