User manual BEGLEC LED DIRECTOR V1.0

[. . . ] `t Hofveld 2 ~ B1702 Groot-Bijgaarden ~ Belgium Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited. Dispose of the unit and used batteries in an environment friendly manner according to your country regulations. Thank you for buying this JB Systems product. To take full advantage of all possibilities, please read these operating instructions very carefully. [. . . ] Press this button to edit the wait time. Can be used in chase playback mode or All 6 outputs use 4 channels, each with the same order: R+G+B+DIM (or DIM+R+G+B ~ see setup menu) 16. dMX OUT: used to connect all LED projectors in a "daisy chain configuration" (all units in one DMX line). The channels of the different projectors are merged to 24 channels: Fixture1 = channels 001 to 004 Fixture2 = channels 005 to 008 Fixture3 = channels 009 to 012 Fixture4 = channels 013 to 016 Fixture5 = channels 017 to 020 Fixture6 = channels 021 to 024 17. DMX IN: normally not used BUT you can connect an external DMX-controller. As soon as a DMX-signal is detected on this input, this DMX-signal takes precedence of the outputs generated by the LED Director. This means that an external DMX-controller can automatically take over the control over the fixtures connected to the DMX-outputs. You can even determine starting from which address the incoming DMX-channels should be routed to the outputs (see item 5 in the chapter "setup menu"). DMX THROUGH: This is an exact copy of the DMX input (17) and is used to daisy chain the LED Director in a big installation. The LED fixtures can be connected to the LED Director in two ways: STAR CONFIGURATION The 6 DMX-outputs (15) are used and the connected LED fixtures all have start address 001. Of course you can put several LED fixtures (ex. 1A and 1B on the drawing) on one output but all should have the same start address 001. All LED fixtures receive their own start address, (see n°16 in the previous chapter) depending on which of the 6 channels you want to assign them to. The setup menu is used to configure the LED Director and perform some less used functions. Press the MENU button (4) for about 1 second to enter the setup menu. The menu contains 11 sections that are fully explained below: 1/ SET DATE Use the dial (14) to select "SET DATE" and press the ENTER button (13) the display shows the current date. Use the dial (14) to select the item you want to edit (year, month or day will be underlined) Press ENTER (13) and use the dial (14) to adapt the value Press ENTER (13) to confirm and also adapt the other values. Turn the dial (14) until the display shows "STORE DATE SET" Press ENTER (13) to confirm. Note: if you want to return to the main menu, just press the MENU button (4) shortly. 2/ SET TIME Use the dial (14) to select "SET TIME" and press the ENTER button (13) the display shows the current time. Use the dial (14) to select the item you want to edit (hours, minutes or seconds will be underlined) Press ENTER (13) and use the dial (14) to adapt the value Press ENTER (13) to confirm and also adapt the other values. Turn the dial (14) until the display shows "STORE TIME SET" Press ENTER (13) to confirm. [. . . ] Note: fade & wait times can only be adapted if you selected "RUN TIME BY CHASE" in the setup menu (see item 5 in the chapter "setup menu") MANUAL MODE: First select one of the chases as described for the automatic mode. Press the PROGRAM button (11) during 1s to enter program mode the green LED blinks while the display shows "Chase [01]" B. Use the dial (14) to choose the desired chase, for example chase 02 C. Press the SCENE button (6) the display shows "C02 SN01" and the eventual scene is shown on the blinking RGB-indicators (2). [. . . ]