User manual BEGLEC LED POWER BANK V1.0 FIRMWARE V12

[. . . ] Ver 1, 0 (firmware V12) USER MANUAL T ABLE OF CONTENTS TABLE OF CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I. PART 1 PRODUCT (GENERAL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 1. 1--PRODUCT INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. 1. 2--PRODUCT FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. 1. 3--TECHNICAL SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. [. . . ] 1, 2, 3. . . Not required for WASH programs). ID ON should be set in the Settings menu on each unit. When using the PIX CONTROLLER with the fixtures there is no need to set the DMX address. When using the Effect programs it is important to set the Range of fixtures in the Settings menu of the PiX CONTROLLER. Example: ID Addr. 1 ID Addr. 2 ID Addr. 3 ID Addr. 4 ID Addr. 5 ID Addr. 6 ID Addr. 7 ID Addr. 8 ID Addr. 9 CONTROLLER MOD E SETU P UP DO WN In the figure above the PiX controller is connected in series to 9 units with corresponding ID addresses from 1 to 9. Each fixture has ID ON in the fixture's Settings menu. In order to activate the Effect programs in the PIX CONTROLLER, the Range must be set to 009 in the Settings menu of the PIX CONTROLLER. (Note: it is possible to create different kinds of effects by changing the direction and position of ID Addresses) 2 INSTALLATION 12 2007. 9. 8 2. 5-3 REPEAT ROW BLOCK APPLICATION Connect the fixtures to the PIX CONTROLLER in series. ID Address should be set in the Settings menu on each unit in ascending order with each row repeated (Not required for Wash programs). ID ON should be set in the Settings menu on each unit. When using the PRO-a CONTROLLER with the fixtures there is no need to set the DMX address. When using the Effect programs it is important to set the Range of fixtures in the Settings menu of the PRO-a CONTROLLER. Example: ID Addr. 1 ID Addr. 2 ID Addr. 3 ID Addr. 1 ID Addr. 2 ID Addr. 3 ID Addr. 1 ID Addr. 2 ID Addr. 3 CONTROLLER MOD E SETU P UP DO WN In the figure above the PIX controller is connected in series to 9 fixtures with each row comprising of 3 fixtures with corresponding ID addresses from 1 to 3. Each row is repeated so that the ID addresses appear the same was as the first row. Each fixture has ID On in the fixture's Settings menu. In order to activate the Effect programs in the PIX CONTROLLER, the Range must be set to 003 in the Settings menu of the PIX CONTROLLER. 2 INSTALLATION 13 2007. 9. 8 2. 6 OPERATION: DMX512 Vs PiX CONTROLLER OPERATION WITH A DMX512 CONTROLLER AVAILABLE FUNCTIONS BENEFITS DRAWBACKS DMX512 ADDRESS ID ADDRESS X Basic WASH Programming X Advanced WASH & EFFECT programming No need to set up DMX Address or ID Address Must locate previosly stored DMX Address DMX512 ADDRESS ID ADDRESS Units are fully controlled from DMX512 controller X X Programming requires many DMX channels No auto programs DMX512 ADDRESS ID ADDRESS Basic WASH programming & ADAS DMX Address ID address allows for less DMX channels when programming* ADAS User can switch be tween ADAS & real DMX address Advanced fixture mapping No auto programs All ID addresses must be set DMX512 ADDRESS ID ADDRESS Advanced WASH & EFFECT programming & ADAS No auto programs All ID addressesmust be set OPERATION WITH THE PiX CONTROLLER AVAILABLE FUNCTIONS BENEFITS DRAWBACKS DMX512 ADDRESS ID ADDRESS X X Play WASH auto programs, Basic CUSTOM programming & Schedule play Play WASH auto programs, Basic CUSTOM programming & Schedule play Play WASH & EFFECT auto programs, Advanced CUSTOM programming & Schedule play No need to set up DMX Address or ID Address Only control of all units at the same time DMX512 ADDRESS ID ADDRESS DMX address not used Only control of all units at the same time X X DMX512 ADDRESS ID ADDRESS DMX Address not used Control speed and time of all WASH & EFFECT programs Create powerful CUSTOM programs Schedule play Trigger auto programs with DMX IN DMX Address not used Control speed and time of all WASH & EFFECT programs Create powerful CUSTOM programs Schedule play Trigger auto programs with DMX IN All ID Addresses must be set DMX512 ADDRESS ID ADDRESS Play WASH & EFFECT auto programs, Advanced CUSTOM programming & Schedule play All ID Addresses must be set 2 INSTALLATION 14 2007. 9. 8 3 DISPLAY PANEL OPERATION 3. 1 3. 2 3. 3 3. 4 3. 5 3. 6 3. 7 3. 8 BASIC MENU CREATING A STATIC COLOR DMX512 SETTINGS ACTIVATING AN AUTO PROGRAM CHANGING THE SETTINGS A CTIVATE THE PASSWORD POWER ON/OFF 3 DISPLAY PANEL OPERATION 15 2007. 9. 8 3. 1 BASIC The LED fixture is mounted with a LCD display and 4 control buttons. SET UP DOWN EXIT enter the currently selected menu or confirm the current function value scroll 'UP' through the menu list or increase the value of the current function scroll 'DOWN' through the menu list or decrease the value of the current function exit from the current menu or function 3 DISPLAY PANEL OPERATION 16 2007. 9. 8 3. 2 MENU MENU Static color Dimmer Red Green Blue Color macros Strobe Dimmer Red Green Blue Colormacros Strobe 0 0 0 0 0 0 255 255 255 255 255 255 DMX512 Address Personality Address 1 STAGE 1 STAGE 2 ARC 1 512 Auto program Auto Auto Auto Auto Auto Auto Auto Auto 1 2 3 4 5 6 7 8 Set ti n gs ID address ID address 001 066 ID ON/OFF ID ON/OFF RAS ON/OFF RAS ON/OFF ADAS ON/OFF ADAS fader no 01 244 Copy ON/OFF Reset confirm ADAS ON/OFF ADAS fader no Copy ON/OFF R e se t to Factory settings MENU Passw ord Password ON/OFF Password ON/OFF Set Password Set password 3 DISPLAY PANEL OPERATION 17 2007. 9. 8 3. 3 CREATING A STATIC COLOR MENU Static color Dimmer Red Green Blue Color macros Strobe Dimmer Red Green Blue Colormacros Strobe 0 0 0 0 0 0 255 255 255 255 255 255 Static colour Combine RED, GREEN and BLUE to create an infinite range of colors (0-255) Enter Color macros allow to choose 18 color macros Set value of dimmer (0-255) Set the value of the strobe (0-20Hz) 3. 4 DMX512 SETTINGS MENU DMX512 Address Personality Address 1 STAGE 1 STAGE 2 ARC 1 512 DMX512 address Enter the DMX address mode to set the DMX address Activate control from outside source by activating ON Enter Personality mode to choose DMX mode: STAGE 1 ARC 1 , STAGE 2 or 3 DISPLAY PANEL OPERATION 18 2007. 9. 8 3. 5 ACTIVATING AN AUTO PROGRAM MENU Auto program Auto Auto Auto Auto Auto Auto Auto Auto 1 2 3 4 5 6 7 8 Auto Program Select the target Auto mode and press Set to display 3. 6 CHANGING THE SETTINGS MENU Set ti n gs ID address ID address 001 066 ID ON/OFF ID ON/OFF RAS ON/OFF RAS ON/OFF ADAS ON/OFF ADAS fader no 01 244 Copy ON/OFF Reset confirm ADAS ON/OFF ADAS fader no Copy ON/OFF R e se t to Factory settings Settings Enter the ID Address to set the ID address for the unit Enter ID ON/OFF in order to allow/disallow ID address function from the DMX512 controller RAS ON/OFF reserve for future use. In ADAS ON/OFF select allow/disallow Automatic DMX512 Addressing System (ADAS) Enter the ADAS fader no to set the number of channel faders in each layer of the controller In the Copy ON/OFF menu select whether to allow copy of DMX and ID address to unit. Enter the Reset to Factory Settings in order to reset to default factory settings. 3 DISPLAY PANEL OPERATION 19 2007. 9. 8 3. 7 A CTIVATE THE PASSWORD MENU Passw ord O N / OF F Set Password Password ON/OFF Password Enter the Password mode to set password YES/NO When password is activated, display will demand password each time the fixture is powered on. Enter the Set password menu to change password. Set new password using the UP & DOWN keys. Input an 8 digit password and then press SET to confirm NOTE: In the event that the password is forgotten. Please use the factory password shown below. UP > DOWN > UP > DOWN > UP > UP > DOWN > DOWN 3. 8 POWER ON/OFF TURN OFF When display shows MENU , hold down the EXIT key for 3 seconds to turn off power. TURN ON When display is off, hold down the EXIT key for 3 seconds to turn on power. 3 DISPLAY PANEL OPERATION 20 2007. 9. 8 4 USING A DMX512 CONTROLLER 4. 1 4. 2 4. 3 4. 4 BASIC ADDRESSING CHANNEL ASSIGNMENT BASIC INSTRUCTIONS FOR DMX512 OPERATION PROGRAMMING WITH A DMX512 CONTROLLER: EXAMPLES 4 USING A DMX512 CONTROLLER 21 2007. 9. 8 4. 1 BASIC ADDRESSING Connect all of the units in series using standard DMX512 signal cable or the IP65 rated cable provided. [. . . ] 1 to select RED for all MODULES (ID Add. 2) to select NO GREEN for all MODULES (ID Add. 2) to select NO BLUE for all MODULES (ID Add. 2) to select DMX MODE 1 to select ID Add: 2 ID Addr. 1 ID Addr. 2 ID Addr. 1 ID Addr. 2 Step 7 CH3 CH9 CH10 CH1 CH2 Step 8 CH3 CH9 CH10 Red Green Blue 4 USING A DMX512 CONTROLLER 38 2007. 9. 8 EXAMPLE 3 Before any operation is performed on the DMX512 controller, confirm that all DMX channels are set to zero. CH1 CH2 255 0 0 0 11 0 255 0 0 12 0 0 255 0 13 0 0 0 0 11 0 0 0 0 12 to select RED for all MODULES (ID Add. 1) to select NO GREEN for all MODULES (ID Add. 1) to select NO BLUE for all MODULES (ID Add. 1) to select DMX mode 1 to select ID Add. [. . . ]