User manual BEGLEC LED POWER BEAM V1.0

[. . . ] 2. 4-3--REPEAT ROW BLOCK APPLICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11. 2. 5--OPERATION WITH DMX512 Vs PiX CONTROLLER. . . . . . . . . . . . . . . . . . . . . . . 12. PART 3 DISPLAY PANEL OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13. 3. 1--BASIC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14. 3. 2--MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15. 3. 3--CREATING A STATIC COLOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16. 3. 4--DMX512 SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16. [. . . ] DO NOT stand close to the equipment and stare directly into the LED light source. Always disconnect the power supply before attempting and maintenance. Always make sure that the supporting structure is solid and can support the combined weight of the products. The earth wire must always be connected to the ground. Do not touch the power cables if your hands are wet. ATTENTION This product left the place of manufacture in perfect condition. In order to maintain this condition and for safe operation, the user must always follow the instructions and safety warnings described in this user manual. Avoid shaking or strong impacts to any part of the equipment. Make sure that al parts of the equipment are kept clean and free of dust. Always make sure that the power connections are connected correct and secure. If there is any malfunction of the equipment, contact your distributor immediately. When transferring the product, it is advisable to use the original packaging in which the product left the factory. Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired. The lamp (LED) shall be changed if it has become damaged or thermally deformed. 1 PRODUCT(GENERAL) 5 2007. 03. 10 2 INSTALLATION 2. 1 2. 2 2. 3 2. 4 MOUNTING POWER CONNECTIONS SETTING UP WITH A DMX512 CONTROLLER 2. 3-1 DMX512 ADDRESSING WITHOUT ID ADDRESSING 2. 3-2 DMX512 ADDRESSING WITH ID ADDRESS SETTING UP WITH THE PiX CONTROLLER 2. 4-1 SINGLE ROW APPLICATION 2. 4-2 STANDARD BLOCK APPLICATION 2. 4-3 REPEAT ROW BLOCK APPLICATION 2. 5 OPERATION: DMX512 Vs PiX CONTROLLER 2 INSTALLATION 6 2007. 03. 10 2. 1 MOUNTING HANGING The LED PAR can be mounted in a hanging position using the supporting bracket. The bracket should be secured to the mounting truss or structure using a standard mounting clamp. Please note that when hanging the unit a safety cable should also be used. UPRIGHT The LED PAR can be mounted in an upright or sitting position using the supporting brackets. The LED MODULE can be mounted at any angle and in any position. It is possible to further adjust the angle of the LED MODULE using the two adjustment knobs located on the side of the fixture. 2. 2 POWER CONNECTIONS @ 220V: 40 units may be connected in series @120V: 20 units may be connected in series 2 INSTALLATION 7 2007. 03. 10 2. 3 SETTING UP WITH A DMX512 CONTROLLER 2. 3-1 DMX512 ADDRESSING WITHOUT ID ADDRESSING Connect the DMX512 controller to the units in series. Each unit has 9 DMX channels so the DMX Addresses should increase by increments of 9 (e. g. 1, 10, 19, 28. . . ) The ID address has not been set so therefore when using the controller CH8 must be inactive ( CH8=0 ). Each DMX Address may be used as many times as required. Any DMX address in the range from 001 to 500 may be used. Example: DMX Addr. 1 DMX Addr. 10 DMX Addr. 19 DMX512 CONTROLLER The figure above shows a simple DMX512 layout with the starting address of the first unit set at 1, with the second set at 10 and so on. . . (Note that when used in this way, the CH8 ID function must be inactive (CH8=0)) 2. 3-2 DMX512 ADDRESSING WITH ID ADDRESS Connect the DMX512 controller to the units in series Each unit has 9 DMX channels so the DMX Addresses should increase by increments of 9 (e. g. 1, 10, 19, 28. . . ) Each DMX Address may be used as many times as required. [. . . ] Reset to factory settings This functions will reset all settings to the original factory setting. Note that Custom program settings will not be affected by this function Default settings Schedule all times in the schedule are reset to 00:00 Wash program step times and fade times are reset to 001 Effect program speeds are reset to 001 DMX address DMX address is reset to 001 Range range is reset to 066 Allow edit allow edit is reset to Yes Password ON/OFF password is reset to OFF Set password password is reset to 00000000 ('DOWN' = 0, 'UP' = 1) 5 USING THE CONTROLLER 30 2007. 03. 10 5. 9 ACTIVATE THE PASSWORD MENU Passw ord O N / OF F Set Password Password ON/OFF Password Enter the Password mode to set password YES/NO When password is activated, display will demand password each time the fixture is powered on. Enter the Set password menu to change password. Set new password using the UP & DOWN keys. [. . . ]