User manual BEGLEC LS-WH-DMX CONTROL V 1.0

[. . . ] 3. 8--ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 9--FAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 10--EDIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11. 3. 11--SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12. [. . . ] 4. 3--BASIC INSTRUCTIONS FOR DMX512 OPERATION (STAGE 1). . . . . 16. PART 5 APPENDIX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17. 5. 1--TROUBLE SHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17. 5. 2--MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18. 1 1. 1 PRODUCT (GENERAL) PRODUCT INTRODUCTION This product is designed for indoor use. Suitable applications include wash or effect lighting for architectural, stage or nightclub applications. This product can also be installed for use in signage and advertising using the dynamic functions available with DMX512 control. Direct input of DMX512 signal allows the units to be controlled from any DMX512 controller. This product can be operated as a single unit or in multiple units for large applications. The specially developed controller that allows the product to be controlled independent of the DMX512 controller enables the user to create and edit a wide range of custom programs. All programs can be touch-button displayed or scheduled to START and END at scheduled times. When programs have been created or edited in the controller, it is also possible to trigger these programs using the DMX IN function when connected to a DMX512 controller. 1. 2 PRODUCT FEATURES LED FIXTURE * RGB Dimmer 0-100% * Strobe * Automatic programs * LCD display * Display control 'lock-out' * Direct DMX512 input * Independant ID address * Stand-alone/ Slave 1 PRODUCT(GENERAL) 1 2009. 12. 9 1. 3 TECHNICAL SPECIFICATIONS LED MODULE LED MODULE: Voltage Rated Power LED/Unit Output/LED 100~240V. . . 50/60Hz 30W 18pcs (6 x RED / 6 x GREEN / 6 x BLUE) 1W ~40 Environment Temperature -20 Cooling Dimensions Weight Forced air convection 240 x 210 x160mm 2. 5Kg 1 PRODUCT(GENERAL) 2 2009. 12. 9 1. 4 PHOTOMETRIC DATA PHOTOMETRIC DATA 1 PRODUCT(GENERAL) 3 2009. 12. 9 1. 5 SAFETY WARNING IMPORTANT ALWAYS READ THE USER MANUAL BEFORE OPERATION. Each unit has 9 DMX channels so the DMX Addresses should increase by increments of 9 (e. g. 1, 10, 19, 28. . . ) The ID address has not been set so therefore when using the controller Ch9 must be inactive ( CH9=0 ). Each DMX Address may be used as many times as required. Any DMX address in the range from 001 to 512 may be used. Example: The figure above shows a simple DMX512 layout with the starting address of the first unit set at 1, with the second set at 10 and so on. . . (Note that when used in this way, the CH9 ID function must be inactive (CH9=0)) 2. 3-2 DMX512 ADDRESSING WITH ID ADDRESS (STAGE 1 MODE) Connect the DMX512 controller to the units in series Each unit has 9DMX channels so the DMX Addresses should increase by increments of 9 (e. g. 1, 10, 19, 28. . . ) Each DMX Address may be used as many times as required. Any DMX address in the range from 001 to 512 may be used. Each DMX address may carry up to 66 separate ID addresses. ID should be set in the menu on each unit in ascending values (i. e. 1, 2, 3. . . ) ID addresses are accessible from Ch9 on the DMX512 controller. 2 INSTALLATION 6 2009. 12. 9 Example: The figure above shows a simple DMX layout which has used three units at each DMX address. The three units have different ID addresses which allows the user to collectively control the whole group of units at that DMX address by setting CH9 to 0, or to control each unit independently by first selecting the DMX address and then by using Ch9 to locate the target ID address. 2 INSTALLATION 7 2009. 12. 9 3 3. 1 DISPLAY PANEL OPERATION BASIC MENU scroll through the main menu or exit from the current menu or function ENTER Enter the currently selected menu or confirm the current function value UP DOWN scroll 'UP' through the menu list or increase the value of the current function scroll 'DOWN' through the menu list or decrease the value of the current function 2 INSTALLATION 8 2009. 12. 9 3. 2 MENU 3 DISPLAY PANEL OPERATION 9 2009. 12. 9 3. 3 STATIC STATIC Select RED / GREN / BLUE / STRB to set the value 3. 4 AUTO AUTO Select the target AUTO program and press ENTER Programs AUTO 1 to AUTO 10 are fully pre-programmed and will not be altered Programs Custom 1 to Custom 10 are fully pre-programmed and can be edited 3. 5 ADDRESS ADDRESS Enter ADDRESS and set the DMX address 001~512 3. 6 RUN RUN Enter RUN to choose SLAVE or DMX working mode 3 DISPLAY PANEL OPERATION 10 2009. 12. 9 3. 7 PERSON PERSON Enter PERSON and select STAGE1 / ARC1 / ARC1+D DMX mode 3. 8 ID ID Enter ID and set the ID address 001~066 3. 9 FAN FAN Enter Fan and select the working mode of fan: High Normal , Auto or Low . [. . . ] to upload the custom programs from the current MASTER unit to the SLAVE units COLOR is f ora ctivate/unactivatet hec olorc alibrationf unctions. When [UC] is selected, the RGB output are adjusted to a standard preset universal color which balances fixtures from different generations. . The factory default setting is [UC] on. 3. 12 PASSWORD PASSWORD Enter the PASSWORD mode to select whether the access password is on or off. When the fixture is set as PASS ON , after 30 seconds or turn on the fixture next time, the fixture will need an access password to enter the display menu control. [. . . ]