User manual BEGLEC Z-1020

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BEGLEC Z-1020. We hope that this BEGLEC Z-1020 user guide will be useful to you.

Lastmanuals help download the user guide BEGLEC Z-1020.


Mode d'emploi BEGLEC Z-1020
Download
Manual abstract: user guide BEGLEC Z-1020

Detailed instructions for use are in the User's Guide.

[. . . ] Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Fog Machine for years to come. Please follow these operation, safety and maintenance instructions to ensure a long and safe life for your fog machine. Drain all fog liquid from the tank, pack the unit securely (preferably in the original packing material), and return it to your ANTARI dealer for service. [. . . ] Plug power cord into a grounded electrical outlet. Turn the power switch to "ON" on the back of the The unit will take a couple of minutes to warm up the heater. During this time the machine cannot generate fog. When the remote control is attached the red lights (on Z-800II handle) and green light (on the remote) will flash and stay ON when the warm-up time is complete. For further information on operating your ANTARI Z-800II, Z-1000II and Z-1020 Fog Machine, see the section titled "Remote Control Operation". Because this may result in some Important: Always monitor tank fluid level as you are fogging. Running a fog machine with no fluid can permanently damage the unit. If your model includes a mounting bracket designed for overhead installation, it may be installed at floor level or suspended overhead. If the unit is to be mounted using the bracket, it is important that the fog does not shoot directly at any one's face. Whatever installation method you choose, do not allow the unit to have more than a 15 degree angle of inclination. If you experience low output, pump noise or no output at all, unplug immediately. Check fluid level, the external fuse, remote control connection and power from the wall. If fog does not come out after holding the remote button down for 30 seconds, check the hose attached to the tank to make sure there is fluid going through the hose. If you are unable to determine the cause of the problem, do not simply continue pushing the remote button, as this may damage the unit. Return the machine to your ANTARI dealer. Moisture accumulation on the surface below the output nozzle, consider this condensation when installing your unit. All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so after being turned off. All fog machines have a recycling period after long bursts when the machine will shut itself down for a short period in order to heat up again. During this time no fog can be produced. Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid container and the fog machine liquid tank immediately after filling. After every 40 hours of continuous operation, it is recommended to run a cleaning solution composed of 80% distilled water and 20% white vinegar through the system to prevent the accumulation of particulate matter in the heating element. [. . . ] DMX Setting for Z-1000II and Z-1020 fog machines with on board DMX Channel A Einleitung These two models use 1 channel to control on/off operation. each channel has a value range of 0 to 255. On/Off function can be programmed using the DMX controller or the DMX control software being used by lighting and effects operator. If Channel A has a value from 0 to 128, the unit is OFF. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BEGLEC Z-1020

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BEGLEC Z-1020 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag