User manual BEHRINGER DSP1400P

[. . . ] DSP1400P User´s Manual Bedienungsanleitung Version 1. 0 December 1998 E D ULTRAMIZER PRO ® www. behringer. de 1 EC-Declaration of Conformity INTERNATIONAL GmbH acc. to the Directives 89/336/EWG and 73/23/EWG We, BEHRINGER INTERNATIONAL GmbH Hanns-Martin-Schleyer-Straße 36 - 38 D - 47877 Willich Name and address of the manufacturer or the introducer of the product on the market who is established in the EC herewith take the sole responsibility to confirm that the product: ULTRAMIZER PRO DSP1400P Type designation and article-No (if applicable) to which this declaration refers, is in accordance with the following standards or standardized documents: x EN 60065 x EN 55020 x EN 55013 x EN 61000-3-2 x EN 61000-3-3 x EN 55022 The following operation conditions and installation arrangements have to be presumed: acc. Nier, President Name, address, date and legally binding signature of the person responsible Willich, 01. 12. 1998 2 SAFETY INSTRUCTIONS CAUTION: To reduce the risk of electrical shock, do not remove the cover (or back). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. [. . . ] Start your sequencer and press PRESET on the unit to start the transmission. If you press the IN/OUT key again on the sixth page, the ULTRAMIZER PRO quits MIDI setup mode. To load these settings again, select d1, press PRESET and start your sequencer. If you press IN/OUT again, you will leave the MIDI setup. You can at all times press any other key to leave the MIDI setup directly. + During a bulk dump all audio functions of the ULTRAMIZER PRO will be deactivated. The full-featured MIDI implementation of the ULTRAMIZER PRO allows for easily integrating the ULTRAMIZER PRO into any MIDI system. For detailed information on controller tabs please refer to section 6. 1. s MIDI IN Any MIDI data sent to the ULTRAMIZER PRO (sequencer, MIDI footswitch, etc. ) are received via the MIDI IN jack. For example, if you wish to use the ULTRAMIZER PRO as an effects device for your guitar rack, you can connect the MIDI IN jack to a MIDI footswitch that allows for selecting program presets. If your rack includes another MIDI effects device (e. g. a multi-effects processor), the data sent from the MIDI footswitch can be routed via the ULTRAMIZER PROs MIDI THRU jack to your multi-effects processor. s MIDI THRU The MIDI THRU jack is used to loop through incoming MIDI data, i. e. any control data received at the MIDI IN of the ULTRAMIZER PRO will be transmitted via the MIDI THRU jack to other MIDI devices/instruments. s MIDI OUT The MIDI OUT jack allows for transmitting MIDI data that originate from the ULTRAMIZER PRO. We are currently developing a software editor which will allow for storing single items of the unit`s internal data on an external medium. Thus, it will be possible to archive ULTRAMIZER PRO settings and presets on a computer, sequencer or MIDI data recorder. Both MIDI Control Change and MIDI Program Change commands will be transmitted when you edit or recall filter settings. Detailed information on this future software editor are available from our BEHRINGER hotline (tel. +49 (0) 2154-920666), our international distributors and/or our Internet homepage http://www. behringer. de. E 3. APPLICATIONS The BEHRINGER ULTRAMIZER PRO features a high level of flexibility. The following chapter describes some other possible applications for your ULTRAMIZER PRO. 3. 1 Level setting Take care to set levels properly on the ULTRAMIZER PRO!Low levels deteriorate the dynamics of the music signal, which results in a poor, weak and noisy sound. On the other hand, excess levels overdriving the converters in the ULTRAMIZER PRO should also be avoided. [. . . ] Damages/defects caused by the following conditions are not covered by this warranty: s misuse, neglect or failure to operate the unit in compliance with the instructions given in the user or service manuals. s connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used. s damages/defects that are caused by force majeure or by any other condition beyond the control of BEHRINGER INTERNATIONAL. Any repair carried out by unauthorized personnel will void the warranty. [. . . ]