User manual BEHRINGER SL3242FX-PRO

[. . . ] EURODESK SL3242FX-PRO/SL2442FX-PRO User Manual A50-24413-00002 EURODESK SL3242FX-PRO/SL2442FX-PRO Important Safety Instructions 1) Read these instructions. 5) Do not use this apparatus near water. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. [. . . ] In PFL mode only the left display is active, because the PFL signals are mono. (40) The SOLO/PFL switch determines whether the monitored signal is pre (PFL) or post-fader (SOLO) after pressing the SOLO/PFL switch (the LED illuminates). The level meter indicates the corresponding signal (see (39)). When you adjust a signal with the TRIM control, it is advisable to select PFL mode, so that the level shown is independent of the channel fader position. Fig. 2. 13: Main out fader (33) Use this high-precision MAIN fader to control the output level of the main mix. 8 Control elements and connections EURODESK SL3242FX-PRO/SL2442FX-PRO 2. 6. 1 Talkback The talkback function of the EURODESK allows you to communicate with the musicians in the recording room or on the stage. The talkback signal is present at the AUX SEND outputs, which are particularly useful for monitor/headphone mixes. 2. 7 CD/tape Fig. 2. 20: CD/tape (47) TO MAIN controls the volume of, for example, a CD player connected to the CD/tape input connectors (see (49)). 2. 17: Talkback section (41) The LEVEL control determines the volume of the talkback signal at the AUX 1/2 outputs. (42) Use the TALK TO AUX 1/2 switch to activate the built-in talkback microphone. Its signal is sent to the AUX SEND jacks 1 and 2. Keep the switch pressed while you're speaking. (43) This is the built-in talkback microphone. (48) When the STANDBY switch is pressed, all input channels are muted. Only the CD/tape signal will be routed to the main mix. In this way, you can prevent the microphones from pickung up unwanted sounds or noise that would interfere with CD playback during a break. The main mix and channel faders can remain in their normal positions while playing back music from CD (using the CD/TAPE INPUTs (49)), so you don't lose your mix. 2. 6. 2 Phones & control room Fig. 2. 18: Phones/control room section (44) The PHONES/CTRL R control adjusts the volume of the headphones connected to the PHONES/CTRL ROOM OUT jack (see (46)). If you have an active monitor speaker or power amp connected here, you can also control the monitor volume. (45) These switches select the signal sent to the PHONES/CTRL ROOM jack. Available sources are: MAIN, CD/TAPE, AUX 1/2 and subgroups 1 - 2 and 3 - 4. Fig. 2. 21: CD/tape connectors (49) The CD/TAPE INPUT RCA connectors are for the connection of CD players, tape decks or other line-level sources. The signal volume is adjusted with the TO MAIN control. [. . . ] In case BEHRINGER decides to replace the product, this warranty shall apply to the replacement product for the remaining initial warranty period, i. e one year* from the date of purchase of the initial product. If the warranty claim proves to be justified, the product will be returned to the user freight prepaid. Warranty claims other than those indicated above are expressly excluded. § 6 Warranty transferability This warranty is extended exclusively to the original buyer (customer of retail dealer) and is not transferable to anyone who may subsequently purchase this product. No other person (retail dealer, etc. ) shall be entitled to give any warranty promise on behalf of BEHRINGER. § 4 Return authorization number 1. [. . . ]