User manual BEHRINGER UB502

[. . . ] EURORACK UB502/UB802/UB1002/UB1202 User Manual A50-18013-00005 EURORACK UB502/UB802/UB1002/UB1202 Important Safety Instructions 11) The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection. 12) Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. 13) Use only attachments/accessories specified by the manufacturer. * ! This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. [. . . ] FX SEND The FX SEND output (does not apply for UB502) should be connected to the input of an external effects unit. The post-fader FX signal you created using the input channel FX controls is sent to the effects unit via the FX SEND ouput. Use the FX SEND control of the main section to adjust the overall send level (UB1002 and UB1202 only). 2. 2. 3 FX sends, balance and level adjustment 2. 3. 2 Monitor and main mix Fig. 2. 6: The FX send/balance/level controls FX The FX sends of the stereo channels function similar to those of the mono channels. However, since the FX send buses are both mono, a mono sum is first taken from the stereo input before it is sent to the FX bus. BAL The BAL(ANCE) control determines the levels of left and right input signals relative to each other before both signals are then routed to the main stereo mix bus. If a channel is operated in mono via the left line input, this control has the same function as the PAN control used in the mono channels. LEVEL The LEVEL control determines the volume of the channel being sent to the main mix. +4/-10 The stereo inputs of the EURORACK UB1002 and UB1202 have an input sensitivity switch which selects between +4 dBu and -10 dBV. At -10 dBV (home-recording level), the input is more sensitive (requires less level to drive it) than at +4 dBu (studio level). Fig. 2. 9: Monitor/main mix connectors 2. 3 Connector panel and main section 2. 3. 1 Send/return effects path Fig. 2. 10: Monitor control and main mix fader Fig. 2. 7: FX send/return connectors PHONES/CONTROL ROOM The stereo PHONES jack (at the top of the connector panel) is where you connect headphones. The unbalanced CONTROL ROOM OUT jacks carry the summed effects and main mix signals, as well as soloed channel signals. The PHONES/CONTROL ROOM control adjusts the level of both headphones and main monitor outputs. The UB502 is not equipped with control room outputs. Fig. 2. 8: FX send/return controls 6 Control elements and connectors EURORACK UB502/UB802/UB1002/UB1202 MAIN MIX The MAIN OUT connectors are unbalanced mono jacks. The main mix signal appears here at a level of 0 dBu. The MAIN MIX fader adjusts the volume of these outputs. The EURORACK UB802 and UB502 mixing consoles feature a rotary control for this purpose. 2. 3. 5 Phantom power and LED displays 2. 3. 3 Tape connectors TAPE INPUT The TAPE INPUTs are used to bring an external signal source (e. g. CD player, tape deck, etc. ) into the console. They can also be used as a standard stereo line input, so the output of a second EURORACK or BEHRINGER ULTRALINK PRO MX882 can be connected. [. . . ] § 7 Claim for damages Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim (consequential) damages. In no event shall the liability of BEHRINGER exceed the invoiced value of the product. * Customers in the European Union please contact BEHRINGER Germany Support for further details. Technical specifications and appearance are subject to change without notice. The information contained herein is correct at the time of printing. [. . . ]