User manual BEKO 15WLP530HID

[. . . ] INTEGRATED DIGITAL HD READY COLOUR TELEVISIONS 15WLP530HID Operating Instructions TABLE OF CONTENTS Contents 1 1-Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 Cleaning the screen and cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 2 Disposing of your TV at the end of service life. . . [. . . ] The channel will not be displayed unless the correct password is entered. AccessControl Lock/UnlockChannels ChangePIN 6. 3. 6-Digital Features To enter digital features menu, select FEATURES tab from the main menu by using Up/Down movement buttons. Select DIGITAL FEATURES tab from FEATURES menu by using Up/Down movement buttons and press OK button to confirm. DIGITAL FEATURES menu will be displayed. DigitalFeatures LanguageSettings AccessControl UserInterfaceOptions Timers FavouriteList NoCommonInterfaceModulePresent SystemMenu Select Back Select Back You can select the menu headings with Up/ Down movement buttons to make settings. 6. 3. 6. 1-Language Settings You can select subtitle and sound language provided that the broadcast is supported for all digital broadcasting channels. Unless you make any selection, the language supported by the broadcaster will be selected automatically. Note 1: To re-prevent access after entering the correct password and displaying the restricted channel, your television has to be switched to Standby mode and turned on again. Note 2: The password for both of these features has been set as 0000 at the factory. You can change the password as you wish under Change PIN item in the Access Control menu. 14 6. 3. 6. 3-User Interface Options From this menu, you can decide whether to display the scrambled channels in the program table or not. If List Scrambled Channels is set to ON, all channels will be displayed, if it is set to OFF, scrambled channels will not be displayed and if it is set to AUTO and a CI card is installed to your television, then the scrambled channels supported by the card will be displayed. confirm by pressing the OK button. Press the MENU button on your remote control. Select SETUP tab with Down movement button and confirm with OK button. Setup menu is displayed. SETUP SYSTEM CHANNEL FINETUNE SEARCH PROGRAMNO STORE AUTOPROGRAM I S06 0 P13 6. 3. 6. 4-Timers In this menu you can view Reminders you had entered from the EPG or change or delete the entered Reminders. 6. 3. 6. 5-Favourite Lists Please see 6. 3. 4. 2-Creating favorite channel list, for detailed explanation of this feature. SELECT BACK 6. 3. 6. 6-Common Interface Module In this menu, you can make the CI Module settings that you can attach to your television. 6. 3. 6. 7-System Menu You can display your television's hardware and software data under this menu. Select PROGRAM NO tab by pressing the Up/Down movement buttons in Setup menu, enter the channel number to be searched and stored automatically, then select AUTOPROGRAM tab by using the Up/Down movement buttons and press OK button; Country Selection menu will be displayed. COUNTRYSELECTION BELGIUM CZECHREP. DANMARK DEUTSCHLAND ELLADA ESPANA FRANCE HUNGARY IRELAND ITALIA NETHERLANDS NORGE ÖSTERREICH POLSKA PORTUGAL SCHWEIZ SUOMI SVERIGE TÜRKYE U. K. . . . . . . . . . . . . . . . . . . . . . . . . . . 6. 4-Performing Analog Tunings You can either tune the Analog channels automatically or manually and store them in your television. 6. 4. 1-Automatic tuning of channels and storing in the memory Note: If your television does not receive any antenna broadcast for a period of 5 minutes, it automatically switches to the stand-by position. The countdown OSD is displayed on the screen during the last 1 minute (applicable for Analog mode only) You can tune the programs automatically with the Autoprogram function of your television and then sort the channels as you desire by means of the Program Table. Press AV button on your remote control, select ANALOG tab from the SOURCE menu by using Up/Down movement buttons and STARTAUTOPROGRAMMING BACK In the Country Selection menu, select the country, whose broadcast you would like to watch in priority, by pressing the right/left movement buttons and start autoprogramming by pressing the OK button. The channels will be automatically searched and those found will be stored in memory starting from the program selected in the Setup menu. At the same moment, the Autoprogram menu will be displayed and a marker indicating the progress of the autoprogramming will appear as shown below. AUTOPROGRAM SEARCHING %20 STOP 15 To stop the process at any given time, please press the MENU button. The Program Table, which will allow you to sort the channels as you wish, will be displayed after the automatic search is complete. 6. 4. 2. 2-If you do not know the channel number Press the MENU button. Move to the SETUP menu by pressing the Down movement button in the Main Menu and confirm your selection with the OK button. Select the system in which you would like to make the search from the SYSTEM tab. Move into CHANNEL tab by pressing the down movement button. Press OK on your remote control to select "S" for cable channels and "C" for channels received via the antenna. Select SEARCH tab using the Up/Down movement buttons, and scan the channels in ascending order with Right movement button and in descending order with Left movement button. [. . . ] Television channel (no teletext) or antenna system. Very weak signal Temporary sound mute may be on No or defective teletext No sound Is the sound turned down?Remote control does not work Are batteries exhausted?Is there any obstacle between the remote control and television? [. . . ]