User manual BEKO 20LB450

[. . . ] ELECTRICAL CONNECTIONS For your own safety read the following instructions carefully before attempting to connect this unit to the mains supply. For your convenience a mains lead and plug with a fuse has been supplied. For your safety please observe the following information. Should the fuse need to be replaced an ASTA approved BS 1362 fuse of the same rating must be used. [. . . ] If the program you are viewing is available in stereo, then this will be indicated with STEREO on screen display. Spatial To give further "depth" to the sound of the program you are watching, select "Spatial" using right movement button ( ) in Sound Mode. You can control the sound settings of your television by using the ( ) and ( ) buttons on your remote control or the buttons directly on your television. To set up other features of the sound menu, press the ( ) button on your remote control. Select the SOUND menu bar in blue, press the ( ) button and the SOUND menu will appear on screen. Using the up-down movement buttons ( )/( ) you can choose the features that you require. Balance In order to balance the level of sound between the right and left speaker of the television, use the down movement button ( ) to highlight the BALANCE mode in white and by using the right left buttons ( )/( ), you can adjust the balance. -15- Equalizer Highlight "EQUALIZER" in the SOUND MENU, press the ( ) button bringing the equalizer setting function on screen. Using the up-down movement ( )/( ) buttons you choose between a series of preset settings for different types of sound output such as Music, Sports, Cinema and Speech. Also you have the Personal 1 and Personal 2 option settings which can be adjusted in accordance to your preferences. Highlight the Personal preferences, press ( ). Then by using the right-left movement ( )/( ) buttons choose from the 120Hz / 500 Hz / 1, 5KHz / 5KHz / 10 KHz frequencies and with the up-down movement ( )/( ) buttons, adjust the levels according to your preferences. To store the frequency levels, press the ( ) button and then your preferences will be stored in the memory of your television. To exit at any given stage, press the ( ) button. You can choose the equalizer modes directly from the ( ) button of your remote control. When you plug in the headset and press the MUTE button sound is transferred into the headset. In the event that you wish to exit stage, press the ( ) button. Please note: If you turn your television off from the main power supply switch then the sleep timer modes selected will cancelled. By pressing the ( ) button on your remote control, you have the ability to change the picture format of the screen. If you leave the screen format function on AUTO then the program that you are viewing will be shown in either 4:3 or 16:9 format depending on the transmission broadcast. A black band may be present top and bottom of the picture dependant on the broadcast this is not a fault. TIME SELECT ON TIME SELECT OFF TIME In the FEATURES MENU use the numeric buttons to enter the time. The time that is stored here will be used as the basis in all activities based within the TIMER mode. Please Note: The time will be reset when you turn off your television, but will adjust itself to the time of any channel with Teletext once you switch on your television again, getting the necessary information from the transmission. In the FEATURES MENU highlight the TIMER option and press ( ), which will bring the SLEEP TIMER menu on screen. With this function, you will have the ability to automatically turn your television on or off at the time of your choice, or enable your television to shift from one channel to another at a time of your choice. Picture Format SLEEP TIMER Mode -18- Using Teletext Teletext is an information system that displays text on your TV screen. Using the teletext control buttons you can view pages of information that are listed in the teletext index. Please Note: No on screen display is available in text mode. [. . . ] In order to make the necessary adjustments in this menu, you can use the right-left, up-down movement ( )/( ), ( )/( ) buttons on your remote control. PHASE: ADC's phase setting H. POSITION: Horizontal position setting V. POSITION: Vertical position setting AUTOMATIC CONFIGURATION: The most suitable geometric settings in accordance to the entry mode is configured by this function. For this application, highlight the AUTOMATIC CONFIGURATION option and press the OK button. Warning Messages: 1. Under these circumstances the on screen display will be "NO SIGNAL". [. . . ]