User manual BEKO CWB 9831 ANP

[. . . ] Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities. This product was manufactured using the latest technology in environmentally friendly conditions. The Instructions for Use apply to several versions of this appliance. [. . . ] Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. Do not flambè under the range hood; risk of fire ?This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. "CAUTION: Accessible parts may become hot when used with cooking appliances. Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. Clean and/or replace the Filters after the specified time period (Fire hazard). Clean the hood using a damp cloth and a neutral liquid detergent. Light, Suction Unit, Filters, Lower Duct 7 1 PVC Pipe (fitted) 8 1 Inclinable grid (fitted) 9 1 Reduction flange ø 150-120 mm 10 1 Metal cover Width Depth Height Supply voltage Control Suction power Motor power Lamp power Fuse Air outlet pipe diameter Net weight Gross weight Color Markings on the product or the values stated in other documents supplied with the product are values obtained under laboratory conditions as per relevant standards. These values may vary according to the usage of the product and ambient conditions. If you want to use the hood in suction version with the air outlet at the back of the hood, make sure to follow the indications given below in the drawing for a correct boring operation of the air outlet opening. When installing the hood in recycling version it has to be taken into consideration that space remaining between the hood and the upper limit (ceiling or self) is at least 8-10 cm. on the wall , trace: · A vertical line up to the ceiling or top limit, at The centre of the area where you intend to fit the hood; · As shown, mark a reference point at 847 mm above the horizontal reference line, and at X mm (X= see table in figure) to the right of the vertical reference line. Repeat this operation on the opposite side, checking levelling. Drill the points marked using a ø 12 mm bit · Insert plugs with screws and brackets 11a in the holes then tighten them. As shown, mark a reference point at 53 mm above the horizontal reference line, at the center of the of the vertical reference line. Drill the points marked using a ø 8 mm bit. Remove the metal grease filters by turning the handles provided. Hook the hood canopy onto the two brackets 11a. From inside the hood canopy, adjust the screws Vr to set the Hood Canopy level. When installing the hood in ducting version, basing on the installer's choice, a rigid or a flexible pipe with a ø 150 or 120 mm is used in order to connect the hood to the air outlet piping. The pipe connection can be made on the upper part or on the rear side of the hood. [. . . ] Connect the hood to the mains through a twopole switch having a contact gap of at least 3 mm. Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. Led Leds off Leds C-D-E-F light up according to the speed that is set Lights up when speed 1 is active Lights up when speed 2 is active Lights up when speed 3 is active Lights up when Intensive speed is active Leds C-D-E-F light up according to the speed that is set Turns the lights ON/OFF at maxi- Led H lights up Press and hold the button for 2 Seconds to turn the lights on at in- The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. [. . . ]