User manual BEKO CWB6441X

[. . . ] The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0, 04 mbar to prevent fumes being drawn back into the room by the cooker hood. In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks. Regulations concerning the discharge of air have to be fulfiled. [. . . ] - If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating Boiler then its flue must be of the room sealed or balance flue type. - If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. - When the range hood and appliance supplied with energy other than electricity are simultaneously in op- Eration, the negative pressure in the room must not exceed 4 Pa (4x10-5 bar). - The ducting system for this appliance must not be connected to any ventilation system which is being used For any other purpose. - The ducting system for this appliance must not be connected to any existing ventilation system which is Being used for any other purpose. - Do not leave naked flames or carry out flambè cooking under this cooker hood. - This appliance is not intended for use by persons (including children) with reduced physical, sensory or Mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. - Children should be supervised to ensure that they do not play with the appliance CONNECTING THE POWER CABLE TO THE MAINS POWER SUPPLY Before installation, check that the mains voltage indicated on the rating plate inside the appliance corresponds to the voltage available in your home. The cooker hood must be installed centrally over a cooking appliance. The minimum distance between the cooking surface and the metal grease filters on the underside of the hood must be at least 650mm. To install the hood proceed as follows: 1) Drill six 8mm diameter holes at X1-X2-J and insert the plastic rawl plugs supplied as illustrated in fig. 2 ensuring The brackets are fitted as shown in the blow up. 2) Secure the two brackets C to the wall inserting two of the screws supplied through the two holes on line X1-X2 3) Slide the canopy down the wall to locate the key hole over the washer then secure the canopy to the wall by in- Serting two of the screws supplied through the two outer holes in the rim of the canopy J1 and J2 as illustrated in fig. When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ø 150 or 120 mm, the choice of which is left to the installer. To install a ø 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. Fix the pipe in position using sufficient pipe clamps (not supplied). When the hood is fitted in the recirculation mode the Air Outlet Connection H should be fitted as illustrated in fig. Fit the (optional) charcoal filters by repeating the following operation on each side of the motor housing. Place the two key hole slots in the filter L and turn the filter clockwise to lock the filter in position as illustrated in fig. WARNING: It is a possible fire hazard if the metal grease filters are not cleaned and the charcoal filters replaced regularly. fitting The Chimney 5) FITTING THE CHIMNEY UPPER To fit the upper chimney A, place the top edge of the chimney over the bracket C as illustrated in fig. 8 and secure the chimney using two of the 2. [. . . ] IMPORTANT: When using a gas hob in connection with the cooker hood never leave the burners of the hob uncovered while the hood is in use or when the pans have been removed. It is very important to follow all instructions for cleaning the hood and filters. There could be a possible fire hazard if the filters are not replaced according to these instructions. ATTENTION: The manufacturer declines all responsibility for any damage or injury caused as a result of not following the instructions for installation, for maintenance and replacement times of filters indicated (in order to avoid a possible risk of fire when the filters are saturated with grease). [. . . ]