User manual BEKO GT24540CHN
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BEKO GT24540CHN. We hope that this BEKO GT24540CHN user guide will be useful to you.
Lastmanuals help download the user guide BEKO GT24540CHN.
Manual abstract: user guide BEKO GT24540CHN
Detailed instructions for use are in the User's Guide.
[. . . ] Make your old appliance useless : - disconnect the appliance from the supply; - remove the supply cord (cut it); - remove the eventual locks on the door to avoid the blocking of children inside, while playing, and the endangering of their lives. The refrigerating apliances contain insulating materials and refrigerants which require a proper recycling. Original Spare parts will be provided for 10 years, following the product purchasing date. This appliance is not intended for use by person with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. [. . . ] setting up Your product was designed to operate at an ambient temperature between -15°C and +43°C. If the ambient temperature is above +430C, inside the appliance the temperature can increase. Placing it in a warm room, the direct exposure to sunbeams or near a heat source (heaters, cookers, ovens), will increase the energy consumption and shorten the product life. please observe the following minimun distances: 100 cm from the cookers working with coal or oil; 150 cm from the electric and gas cookers. Ensure the free circulation of the air around the appliance, by observing the distances shown in Item 2. Place the appliance in a perfectly even, dry and well ventilated place. Before plugging in the appliance, please make sure that the parameters of the mains in your house (voltage, currect type, frequency) comply to the operation parameters of the appliance. The information concerning the supply voltage and the absorbed power is given on the marking label placed in the back side of the freezer. The manufacturer has no responsibility for any damage to persons, animals or goods which may arise from the failure to observe the specified conditions. The appliance is endowed with a supply cord and a plug (European type, marked 10/16A) with double earthing contact for safety. If the socket is not the same type with the plug, please ask a specialised electrician to change it. The switching off must be possible by taking the plug out of the socket or by means of a mains two-poles switch placed before the socket. operation Before putting into operation, clean the inside of the appliance (see chapter , , Cleaning"). After finishing this operation please plug in the appliance, adjust the thermostat knob to an average position. Leave the appliance work for about 2 hours without putting food inside it. The temperature of the freezer is adjusted by means of the knob assembled on the thermostat (item. The achieved temperatures can vary according to the conditions of use of the appliance, such as: place of the appliance, ambient temperature, frequency of door opening, extent of filling with food of the freezer. The position of the thermostat knob will change according to these factors. The signalling system is placed on the front side of the freezer (Item 5). Green LED shows that the appliance is Red LED damage lights if the Temperature in the freezer is too high. The LED will operate 15-45 minutes after the putting into operation of the freezer, then it must go off. If the LED goes on during the operation, this means that defects have occurred. [. . . ] Unplug the appliance from the mains, take out the lamp and replace it with a new one. The following are not defects Possible noddings and cracks coming From the product: circulation of the refrigerant in the system. In order to keep the temperature at the value you have adjusted, the compressor of the appliance starts periodically. They are redced as soon as the appliance reaches the operation temperature. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BEKO GT24540CHN
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BEKO GT24540CHN will begin.